Meltem M-WRG-II E-F Скачать руководство пользователя страница 56

Страница: 56 / 60

Operating and installation instructions

M-WRG-II P-T (-F, -FC), M-WRG-II E-T (-F, -FC) ventilation units

- 56 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

16.6.2 Circuit diagram (example of a BUSCH-JAEGER three-step rotary switch with

zero position)

Fig. 36: Circuit diagram for wiring M-WRG-II P-T (-F, -FC) / M-WRG-II E-T (-F, -FC) ventilation units with control cable

and optional pushbutton/LED

VDC

+24 VDC

0 V

01 02 03 04 05 06 07 08 09 10

01 02

04 05 06 07 08 09

Board in M-WRG-II P-T (-F, -FC) /

M-WRG-II E-T (-F, -FC)

ventilation unit 1

Board in M-WRG-II P-T (-F, -FC) /

M-WRG-II E-T (-F, -FC)

ventilation unit 2

Three-step rotary switch with

zero position

Optional: pushbutton and LED for intensive

ventilation

Optional: LED for inten-

sive ventilation

Ventilation level I

Ventilation level II

Ventilation level III

Intensive ventilation

NOTICE

Connect terminal 02 (+24 VDC) to one

ventilation unit only.

NOTICE

Feedback signals can-

not be switched togeth-

er to create a single

group signal.

NOTICE

— One to five ventilation units may be connected to the three-step rotary switch and to the inten-

sive ventilation pushbutton. No separate power supply is needed.

— Please note the following if you intend to connect more than one ventilation unit to the three-

step rotary switch:

— The terminals 01 (0 V) of all ventilation units must be connected to one another (see

Fig. 36).

— The terminal 02 (+24 V DC) of the three-step rotary switch may only be connected to the

terminal 02 of a single ventilation unit (see Fig. 36).

— The feedback from multiple ventilation units for intensive ventilation cannot be combined in a

single group signal.

— The total length of the control cable must not exceed 50 m.

Содержание M-WRG-II E-F





























































Результаты поиска

Содержание M-WRG-II E-F

Отзывы:

Похожие инструкции для M-WRG-II E-F

Бренды по названию

Популярные бренды

Meltem M-WRG-II E-F, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание M-WRG-II E-F

Отзывы:

Похожие инструкции для M-WRG-II E-F

Бренды по названию

Популярные бренды