Meltem M-WRG-II E-F Скачать руководство пользователя страница 54

Страница: 54 / 60

Operating and installation instructions

M-WRG-II P-T (-F, -FC), M-WRG-II E-T (-F, -FC) ventilation units

- 54 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

16.4

Overview of the modules

16.4.1 Connection board in the ventilation unit with terminal assignment

Fig. 35: Connection board in the ventilation unit with terminal assignment

NOTICE

DIP switch 2 (item 1 in Fig. 35) is set to the “Taster (pushbutton)” position at the factory. In asso-

ciation with the three-step rotary switch, DIP switch 2 must be set to the “Schalter (switch)” posi-

tion.

16.4.2 Three-step rotary switch with zero position

To operate the ventilation units, you will need a three-step rotary switch with zero position

(provided by the customer). A suitable example is available from BUSCH-JAEGER or

GIRA.
The three-step rotary switch is used to select one of three different ventilation levels/

programs. In the zero position, the ventilation unit is in standby mode.

16.4.3 Optional pushbutton for intensive ventilation and optional LED for feedback

You can start the ventilation unit’s intensive ventilation level with an optional pushbutton

provided by the customer.
If required, you can use an LED to display when the intensive ventilation is active.

Содержание M-WRG-II E-F





























































Результаты поиска

Содержание M-WRG-II E-F

Отзывы:

Похожие инструкции для M-WRG-II E-F

Бренды по названию

Популярные бренды

Meltem M-WRG-II E-F, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание M-WRG-II E-F

Отзывы:

Похожие инструкции для M-WRG-II E-F

Бренды по названию

Популярные бренды