Meltem M-WRG-II E-F Скачать руководство пользователя страница 7

Страница: 7 / 60

Operating and installation instructions

M-WRG-II P-T (-F, -FC), M-WRG-II E-T (-F, -FC) ventilation units

- 7 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

1.2.2 Three-step rotary switch with zero position

The ventilation unit can be operated via a three-step rotary switch with zero position

(provided by the customer). A suitable example is available from BUSCH-JAEGER or

GIRA.
The three-step rotary switch is used to select one of three different ventilation programs.

In the zero position, the ventilation unit is in standby mode.

1.2.3 Optional pushbutton for intensive ventilation

In addition to the three-step rotary switch, an optional pushbutton may be installed for

activating 15 minutes of intensive ventilation at maximum power level.

1.2.4 Optional accessories

Part no. Type

Description

5478-10 M-WRG-FBH

The wireless remote control is used to control, program and

extend the range of functions of all M-WRG-II units. It can

also be used to read the number of operating hours.

5478-20 M-WRG-FT

The 4-way wireless pushbutton switch with LED feedback

allows the M-WRG-II units to be operated wirelessly.

5478-11 M-WRG-ALGH The mobile reader is used to read the number of hours for

which the M-WRG-II units have been in use.

Table 1: Optional accessories

1.3

Target group

These operating and installation instructions are aimed at two target groups:

— Chapters “1 Introduction” to “14 Troubleshooting” are intended for users of the ventila-

tion unit. No special prior knowledge is needed.

— The activities described in chapters “15 Installing the InControl pushbutton sensor”

and “16 Installing the three-step rotary switch with zero position” must only be carried

out by technicians with the following qualifications:

— Training in the installation and commissioning of electrical devices

— Training in electrical hazards and the local safety requirements

— Knowledge of the relevant standards and directives

— Knowledge and observance of this document and all the safety instructions

1.4

EU declaration of conformity

The ventilation units from the M-WRG-II P and M-WRG-II E series manufactured by

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4

82239 Alling

conform to the regulations and standards listed in the EU Declaration of Conformity

provided.

Содержание M-WRG-II E-F





























































Результаты поиска

Содержание M-WRG-II E-F

Отзывы:

Похожие инструкции для M-WRG-II E-F

Бренды по названию

Популярные бренды

Meltem M-WRG-II E-F, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание M-WRG-II E-F

Отзывы:

Похожие инструкции для M-WRG-II E-F

Бренды по названию

Популярные бренды