Meltem 710000 Скачать руководство пользователя страница 37

Страница: 37 / 44

- 37 -

Installation manual

M-WRG-II M

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

9.13

Cladding the installation kit and flat ductwork / flexible pipes on the inside

In this installation example, the inside

is cladded with OSB board and plaster-

board.

►

Make sure that the plaster cover

(item 1 in Fig. 33) is seated in the

wall box (item 2 in Fig. 33).

►

Make a cutout in the OSB board

(item 3 in Fig. 33) with the same

dimensions as the wall box (item 2 in

Fig. 33).

►

If necessary, make a cutout in the

OSB board (item 3 in Fig. 33) with the

same dimensions as the flat ductwork

elbow (item 4 in Fig. 33, only when

connecting a flat ductwork or flexible

pipe system).

► Make a cutout in the plasterboard (item 5 in Fig. 33) with the same dimensions as the

plaster cover (item 1 in Fig. 33).

► If necessary, make a cutout in the plasterboard (item 5 in Fig. 33) with the same

dimensions as the flat ductwork elbow (item 4 in Fig. 33, only when connecting a flat

ductwork or flexible pipe system).

► Place the OSB board (item 3 in Fig. 33) on the wall box (item 2 in Fig. 33) and fix it to

the frame construction.

► Align the cutout in the plasterboard (item 5 in Fig. 33) on the plaster cover (item 1 in

Fig. 33) and fix the plasterboard in position.

Fig. 33:

Cladding the installation kit and flat ductwork /

flexible pipes on the inside

Содержание 710000













































Результаты поиска

Содержание 710000

Отзывы:

Похожие инструкции для 710000

Бренды по названию

Популярные бренды

Meltem 710000, Руководство по установке

Результаты поиска

Содержание 710000

Отзывы:

Похожие инструкции для 710000

Бренды по названию

Популярные бренды