MELINERA HG01313-BS, Инструкции по эксплуатации и безопасности

Страница: 8 / 11

8 GB/IE/NI
Avoid the danger of
death from electric shock!
Before use, ensure that the mains voltage
available is the same as the required operating
voltage for the product (220–240 V∼).
Before connecting the product to the 10 m lead
wire
7
you should always check the product
and the 10 m lead wire
7
for any damage.
Never use the product if you discover that it is
damaged in any way.
This 10 m lead wire
7
of the LED tree
8
is
nonreplaceable. Hence if it becomes damaged
you must dispose of the entire product.
This product does not contain any parts which
can be serviced by the user. The LEDs cannot
be replaced.
Only use the product with the supplied power
adaptor
3
for the type (Model No.
JT-DC24V3.6W-H3 for HG01313-BS /
HG01313B-BS / HG01313C-BS,
JT-DC31V3.6W-H3 for HG04147-BS); all
warranty claims will otherwise expire.
Never open any of the electrical parts or insert
any kind of object into them.
Protect the 10 m lead wire
7
from sharp
edges, mechanical loads and hot surfaces.
Do not install with sharp fasteners or nails.
Always unplug the power adaptor
3
from the
socket before installation, dismantling or cleaning.
Never touch the power adaptor
3
or the LED
tree
8
itself with wet hands.
The product must not be electrically connected
to another device.
If the product is not in use for any length of
time (e.g. holidays), disconnect it from the
power supply.
If you have any questions about the product or
are unsure about any of its aspects, please seek
the advice of an electrical equipment specialist.
The product is only suited for use with the in-
cluded power adaptor
3
(Model No.
JT-DC24V3.6W-H3 for HG01313-BS/
HG01313B-BS/HG01313C-BS,
JT-DC31V3.6W-H3 for HG04147-BS).
Please note that the power adaptor
3
continues
to draw a small amount of power even if the
product is turned off as long as the power
adaptor
3
is plugged into a power outlet. To
switch the product off completely, unplug the
power adaptor
3
from the socket.
The LEDs are not replaceable.
If the LEDs fail at the end of their lives, the
entire product must be replaced.
RISK OF EXPLOSION! Do
not use the product in explosive atmospheres
where flammable vapours, gases or dusts are
present.
Do not expose the product to any strong
vibrations or heavy mechanical stresses.
Make sure the 10 m lead wire
7
is not laid
down in areas where lawn mowers, trimmers,
scissors or similar cutting tools are used.
RISK OF INJURY! Make
sure that, when the LED tree
8
is removed, the
base plate
1
and the ground spike
2
are
also removed, so that they do not present any
risk (e.g. risk of stumbed by the base and
ground spike).
Installation
Note: Remove all packaging materials from the
product.
Remove the individual parts from the packag-
ing and mount the product according to figures
A–E. The site for the LED tree
8
must be
selected in a way that it is erected on a solid,
level and vibration-free base. Anchor the tree
firmly to the ground and make sure that the LED
tree
8
is stable!
Assembly without ground spike
2
(see fig. A1): Use four suitable screws and
dowels (not included) for the selected site un-
derground and mount the base plate
1
.
Make sure that the recess on the tube of the
bottom plate does not apply to the recess
when fixing!
Installation with ground spike
2
(see fig. A2): Anchor ground spike
2
to the
ground and mount base plate
1
on it. When
fixing the standpipe
5
on the pipe of the base