manualshive.com logo in svg

Melco Fast Clamp, Настройка, сборка и регулировка

Поделиться
Скачать
Melco Fast Clamp Скачать руководство пользователя страница 8

 

34877 Rev. B 

8 of 8 

Melco Fast Clamp Instructions 

 

Embroidery Field Adjustment 

1.  Loosen the Clamp Arm Assembly Thumb Screw ¾

 

to 1 full turn and slide the Clamp Arm Assembly to the required 

position mark on the Interface Bracket. You will hear a slight clicking sound each time the Clamp Arm Assembly 
passes over an indicator registration marker. Re-tighten Thumb Screw at desired location. 

2.  Repeat steps above for the other Clamp Arm Assembly. 

Make sure that both Clamp Arm Assemblies are located at the same indicator value (left and right 
side). 

3.  In the machine Operating System software (OS), select the correct hoop from the hoop list. This corresponds 

with the physical location of the Clamp Arm Assemblies. For example, Clamp Arm Assemblies are set to 
indicator mark 9, select “Melco Fast Clamp 9cm” in the hoop list in the OS. 

If the OS displays the hoops in inches, go to Tools>Options>Measurement Units to change the Hoops to cm. 

CAUTION: If the wrong hoop size is chosen in the OS, damage to the Melco Fast Clamp or the machine 
can occur. This means that if the software setting and the width of the Clamp Arm Assemblies on the 
machine do not match, damage to the Melco Fast Clamp or the machine can occur. Having the correct 
hoop size selected and hoop limits set to “ON” will protect the Melco Fast Clamp from colliding with the 
Lower Arm of the machine and prevent the needle from being driven into the Melco Fast Clamp device. 

 

 

 

 

Should you have any questions or need further assistance with operating your Melco Fast Clamp, please do not 
hesitate to call Melco Technical Support at 888-710-8053. 

Содержание Fast Clamp









Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды