Meinberg IMS LANTIME M4000 Скачать руководство пользователя страница 82

Страница: 82 / 138

12 Attachment: Technical Information

12.8.16.1 LNE-GBE Configuration via the Web Interface

If the LNE-GBE operates in an LANTIME system, all network settings can be configured via the web interface
then.

Physical Network Configuration

Net Link Mode:

The network interfaces LAN1 - LAN4 (LNE-GBE)
can be used in 1000 MBIT HALF / FULL duplex mode.

Indicate Link:

LED indication for the selected physical interface,
only if a front display with function keys is available.

Bonding:

to optimize the reliability and the use of a of higher bandwith.

PRP:

As of LANTIME firmware version 7.0, PRP can also be conveniently set
via the web interface menu "Network

→

Physical Network Configuration".

Select the same PRP group for at least two interfaces in the drop-down
menu "Bonding".

IPv6 Mode:

This mode must be activated here.

MAC-Address:

Displays the unique MAC address of the physical interface.

Assigned Virtual
Interfaces:

In the Ethernet Interfaces menu (see below)
virtual network interfaces can be added.

IMS - LANTIME M4000

Date: 2nd July 2020

Содержание IMS LANTIME M4000











































































































































Результаты поиска

Содержание IMS LANTIME M4000

Отзывы:

Похожие инструкции для IMS LANTIME M4000

Бренды по названию

Популярные бренды

Meinberg IMS LANTIME M4000, Руководство пользователя

Результаты поиска

Содержание IMS LANTIME M4000

Отзывы:

Похожие инструкции для IMS LANTIME M4000

Бренды по названию

Популярные бренды