Meinberg IMS LANTIME M4000 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 138

background image

12 Attachment: Technical Information

12.7.1 Important Hints for hot-pluggable IMS Modules

The following points should be strictly observed when replacing IMS modules during operation. Not all IMS
modules are fully hot-pluggable. Of course, it is not possible to replace a power supply unit of a non-redundant
system without first having installed a second power source in operational mode.

The following applies to the individual IMS slots:

PWR:

"hot swappable"

If you operate your system with only one
power supply, a second power supply must
be installed before removing/replacing it
to keep your system functioning.

I/O, ESI and MRI Slots:

"hot swappable".

CLK1, CLK2:

"hot swappable"

Afer the exchange or the installation of a
clock module a rescan of the reference clocks
(Rescan Refclocks) must be executed in the web
interface menu "System".

CPU:

"hot swappable"

The NTP service and access to the web interface
are interrupted while the CPU is disconnected.
Also the management and monitoring functions are
no longer available.

RSC/SPT:

"hot swappable"

The switching function or the distribution of
generated signals is interrupted while the RSC/SPT
is disconnected.

IMS - LANTIME M4000

Date: 2nd July 2020

41

«
...
44
45
46
47
48
...
»

Содержание IMS LANTIME M4000











































































































































Отзывы:

Нет отзывов

Похожие инструкции для IMS LANTIME M4000

Бренд: A10 Networks Страницы: 17

Express5800/R310e-E4

Бренд: NEC Страницы: 86

Бренд: Yeong Yang Страницы: 7

Бренд: Devolinx Страницы: 51

Бренд: IBM Страницы: 56

System x3350 Type 4192

Бренд: IBM Страницы: 84

WECS II 2048/DMX/02

Бренд: Oase Страницы: 67

System x3550 M3

Бренд: IBM Страницы: 160

System x3650 M4 Type 7915

Бренд: IBM Страницы: 192

Бренд: IBM Страницы: 694

System x3755 M3 7164

Бренд: IBM Страницы: 126

Бренд: Cisco Страницы: 40

SIGMABLADE AD106a

Бренд: NEC Страницы: 2

Series3800/S120R-2

Бренд: NEC Страницы: 2

Series3800/S120R-1

Бренд: NEC Страницы: 3

Series3800/S110R-1

Бренд: NEC Страницы: 2

ServerCare Express5800/FT

Бренд: NEC Страницы: 14

Бренд: NEC Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды