manualshive.com logo in svg

Meiko K-Tronic, Руководство по эксплуатации, Страница: 42 / 44

Поделиться
Скачать
Meiko K-Tronic Скачать руководство пользователя страница 42

Operating instructions dishwashing machine model

 

K-Tronic 

 
 

 

Datei:BA-K-tronic_MIKE_9626212_EN_2005-12-01.doc  

 

9626212

 

 

 

42/44 

W e reserv e the right to change execution and construction !  

MEIKO Maschinenbau GmbH & Co. KG,  Englerstraße 3,  D-77652 Offenburg,  Tel.: +49/781/203-0,  Fax: +49/781/203-1121 

 

 

 

Service step 

 

 

 

 

 

 
 

Maintenance 

 

 

Cleaning works

 

 

Daily 

At least once

 

quarterly 

 

At least once

 

or twice a 

year 

 

but 

 

every 

1000 h 

At least once

 

yearly 

 

but 

 

every 

2000 h 

VERY IMPORTANT: 

 

Whenever any electrical components are disconnected and 
reconnected, replaced or repaired, a safety test must be 
conducted, at least on these components!!! 

 

17. Visual check on the machine environment 

Foaming detergents must not be used close to the machine area and not 
in connection with the machine 

 

 

 

 

 

Water treatment installation (if present) 

 

 

 

 

Reverse osmosis installation (visual check); inform customers on the 
necessity of installation maintenance 

 

 

 

 

Demineralisation installation (visual check); inform customers on the 
necessity of installation maintenance 

 

 

 

 

Observe the manufacturer’s operating instructions in all cases 

 

Air gap according to WRC (if present, i.e. for England) 

 

 

 

 

Check the spray pattern for the perlator nozzle (on the water discharge) 

 

 

 

 

Clean / descale the perlator nozzle (on the water discharge) 

 

 

 

 

 

x1

   

 

Maximum suction temperature   fan 0 550 056   

75°C 

 

 

 

Maximum suction temperature   fan 0 550 050   

75°C 

 

x2

   

 

Pump pre-cleaning temperature    

 

according to DIN 10510   

40°C to 50°C   

 

 

 

 

 

Detergent circulation tank temperature   according to DIN 10510    

55°C to 65°C 

x3

   

 

Clean water rinse temperature    

 

 

according to DIN 10510    

80°C to 85°C 

x4

   

 

Dryin temperature   

 

 

 

 

 

 

according to DIN 10510    

not specified (see x

1

) 

 

x5

   

 

Minimum water quality according to the VGG 

 

 

 

Total salt content:   

 

max. 400 

S/cm for porcelain and opal glass 

 

 

 

 

 

 

 

 

 

 

 

max. 100 

S/cm for glass 

 

 

 

 

 

 

 

 

 

 

 

max. 80 

S/cm for stainless steel (cutlery) 

 

The service steps Servicestufen 

 

-

 

 

must be carried out by personnel trained for this purpose. 

  

trained operating personnel 

  

company tradesman after instruction 

  

trained company tradesmen or installation engineers 

  

installation engineers trained by MEIKO 

 

You can document the completed maintenance work on the following pages. Meiko recommends that you enter the 
half-yearly service steps (

 ), and the annual service steps (

). 

 
 

Содержание K-Tronic













































Отзывы:

Нет отзывов