background image

High or low quarter level

The level of quarter storage in the coin tube
is switch-selectable 

(see pages 6,7).

Fewest Coin Payout

Coins of the highest denomination are
selected for change, enabling the changer
to pay out the coins.

Two Moving Parts for Coin
Acceptance and Separation

Valid coins enter the changer through a
solenoid-operated Accept Gate. If the
coin tube for the accepted coin is full, the
coin goes directly to the cash box. If the
coin tube is not full, a solenoid-operated
Separator Gate diverts the coin to the tube.  

Note: Dollar coins, if accepted, are 

always

directed to the cash box.

Escrow

Single price applications -
dependent upon vend price.

Micromech and MDB application -
dependent on the VMC. Refer to the
vending machine manual for escrow
options, if applicable.

Price Setting

Single Price applications - located on the
control board of the changer.

Micromech and MDB application -
dependent on the VMC. Refer to the
vending machine manual for price setting
procedure.

Vend Price Range

Single price applications - 5¢ to $10.00
(all switches in an ON condition).

Micromech and MDB application -
dependent on the VMC.

Individual Coin Tube Overflow

Electronic sensors monitor the full/empty
status of the coin tubes. Each tube is
monitored individually to maximize coins
available for change.

General Information

Table 1:

 

Coin Tube Overflow

Easy Cleaning and Maintenance

No special tools are required for cleaning, or normal
field maintenance of the TRC coin changer. Refer to
page: 15.

Specifications

UL Approval

The TRC-60X0 Coin Changer is UL listed under file
number E 57869.

CSA Approval

The TRC-60X0C Coin Changer is CSA listed under file
number LR 47838.

Unpacking the Changer

Unpack the changer and immediately inspect it for any
possible shipping damage.  

If the unit is damaged:
1) Return it to its original carton, along with packing

materials.  

2) Notify the delivering carrier of damages and request

immediate inspection.

3) Send a letter of intent to file a claim to the delivering

carrier within 72 hours from the time of delivery.  

4) Send a copy of the letter to the shipper.
5) Retain original carton and packing materials for

future use in shipping or transporting the changer.

Note: 

Only the consignee (the person or company

receiving the changer) can file a claim against the carrier
for concealed damages.

Tube

10¢

Tube

25¢

Tube

Low 25¢
Option
Switch
Set to
OFF
Position

Low 25¢
Option
Switch
Set to
ON
Position

Low
Sensor
Level

High
Sensor
Level

6-8

7-8

6-9

6-9

66-67

98-99

68-69

6-9

3

Содержание TRC 6000






















Отзывы: