Meggitt 60-2 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 62

background image

2nd Ed: Nov 01, 01

4-3

SYS 60-2 POH

4.0

Procedures

4.1

Pre-Flight Procedures

NOTE: To perform the system function check, adequate DC voltage
must be supplied to the system, either 12 or 24 VDC, depending on
the aircraft.

4.1.1

Roll Axis

The following is a step by step procedure for preflighting the Roll Axis:

1. Place the A/P Master Switch to the TEST position. This should
result in illumination of all annunciation’s: RDY, HDG, VS, FD, NAV,
ALT, REV, APR, GS, SEL, UP, DN, FAIL, DSABL, TRIM, CAP, and SOFT.
After all annunciation’s are observed, place the A/P Master Switch to
the ON position. If the Turn Coordinator gyro is up to speed, only the
RDY annunciation should remain on.

2. Rotate the heading knob on the Directional Gyro (DG) to position
the bug under the lubber line.

3. Engage the HDG mode, and observe the HDG annunciation. Then
move the DG heading knob left and right. The control wheel should
move in the direction of bug travel. Return the bug to center.

4. Grasp the control wheel and manually turn it left and right to
overpower the roll servo. There should be a noticeable increase in
control wheel friction, no excessive looseness, no ratcheting or noise.

5. Turn on the NAV radio and tune a valid VOR signal. Then engage
the NAV mode, observing the NAV annunciation. Move the VOR/OBS
so that the needle swings left and right. The control wheel should
move in the direction of needle travel. The NAV annunciation should
flash when CDI deflection is over 50%.

6. Select REV mode, and observe the REV annunciation. Again,
rotate the VOR/OBS knob. The control wheel should move opposite
the direction of needle travel. The NAV annunciation should flash
when CDI deflection is over 50%.

7. Channel a nonvalid VOR signal. The NAV annunciation should
flash, and FAIL annunciation should illuminate (if the radio has a
NAV flag output).

8. Disconnect by pressing and releasing the control wheel mounted
A/P disconnect switch. Move the control wheel to ensure freedom of
controls, and check to see that the RDY annunciator is flashing for
approximately 5 seconds to indicate autopilot disconnect.

«
...
24
25
26
27
28
...
»

Содержание 60-2































































Отзывы:

Нет отзывов

Похожие инструкции для 60-2

Бренд: Raymarine Страницы: 76

Бренд: Yamaha Страницы: 4

Бренд: salmson Страницы: 16

Бренд: Aiwa Страницы: 46

Listening System PLS-900

Бренд: Listen Страницы: 2

AERCO AquaSolve AM8408-COM

Бренд: Watts Страницы: 8

Бренд: JVC Страницы: 82

Бренд: JVC Страницы: 84

Drinking Water Kit

Бренд: SpectraPure Страницы: 16

Бренд: Sony Страницы: 21

Бренд: Sony Страницы: 34

Бренд: Sony Страницы: 42

Бренд: Sony Страницы: 50

Бренд: Sony Страницы: 44

Бренд: Sony Страницы: 46

Бренд: Sony Страницы: 48

Бренд: Sony Страницы: 68

Бренд: Sony Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды