Megger Three-Phase TTR Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 70

background image

M

AVTMTTR330 Rev 3 March 2010

10

4.

Connect the Ethernet cable (optional).

If the user chooses to operate the

TTR330 in a remote-control mode, using PowerDB PC software, then
connect the Ethernet cable between the TTR330 and the PC at this time.

5.

Connect the Load-Tap-Changer cable (optional).

If the user chooses to

operate the “Test button” of the TTR330 from a remote distance then,
connect the LTC cable at this time.

6.

Connect the H and X leads (to the TTR330 end only at this time).

With

the clamps disconnected from the UUT, connect the Bayonet Plug on the
Cable labeled “H” to the TTR panel connector also labeled “H”. Repeat this
process for the “X” labeled cable. Ensure each connector is securely fastened
using a clockwise rotation.

7.

Connect the H and X clamps.

With the ON/OFF Switch in the OFF

position, connect the H and X clamps in accordance with Section 4 as
appropriate for the specific transformer type and test to be conducted.

«
...
16
17
18
19
20
...
»

Содержание Three-Phase TTR







































































Отзывы:

Нет отзывов

Похожие инструкции для Three-Phase TTR

WJHD309 - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 101

Бренд: Xylem Страницы: 24

Бренд: dbx Страницы: 2

Бренд: Magtrol Страницы: 83

Бренд: Hanna Instruments Страницы: 2

Бренд: Palstar Страницы: 37

Бренд: LD Didactic Страницы: 2

Smart Probes 115i

Бренд: TESTO Страницы: 17

Universal Analyzers 275E

Бренд: Ametek Страницы: 34

Бренд: Topcon Страницы: 59

Бренд: Aethra Страницы: 2

Бренд: Flymaster Страницы: 7

HydroTracer FLV

Бренд: aboni Страницы: 48

Бренд: OHAUS Страницы: 84

Бренд: A&D Страницы: 2

Бренд: Hanna Instruments Страницы: 24

Бренд: S&T Страницы: 23

EnviroAlert EA200

Бренд: Winland Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды