8
button will pause the recording. An
additional click will resume recording.
All recording files are stored in a folder
named “RECORD” in the root folder
(onboard memory and microSD).
A click on
will begin playback of
recorded files, beginning with the last
recording. If the RECORD folder is
empty, player will beep 3 times.
A click on
or
will skip to the
previous/next recording file. A 2-second
press will skip 5 files backwards or
forwards.
A click on
or
will
reverse/forward 20 seconds* in the
currently played recording file.
*Actual time may vary.
Pressing
for 2 seconds will delete
10
minimum/maximum speed is reached.
Press
again to exit and save the
setting. Pressing any other button will
exit speed control mode without saving
changes.
To reset the speed to normal, enter
speed control mode, then press
again for 2 seconds. Player will return to
playback mode.
*Speed control does not affect recording
speed. It is not saved when switching
modes or turning player off.
PAUSING/
BOOKMARKING
Click
to pause playback. To resume,
click
again or one of the other
navigation buttons.
9
the current recording file and beep 4
times.
Pressing
for 2 seconds will reset the
recording file counter to 000 and beep 4
times.
*If player function is changed while
recording, the file will be saved before
changing mode and some truncation may
occur.
SPEED CONTROL
A 2-second press on
will put the
player in speed control mode allowing
you to adjust the speed for playback.
A click on
or
will adjust playback
speed. The LED will alternate
red
and
green
as you change the speed. Press
and hold will decrease/increase until the
11
To reset the bookmark to the beginning
of the messages, do the following:
1. While in playback mode, click
.
2. After pausing the player, press
for
2 seconds (player will beep once).
3. The bookmark is now reset to the
beginning. You may resume playback or
turn player off.
CHANGE/RESET
THE BOOKMARK
A 2-second press on
will place a
bookmark at the current position (player
will beep 3 times). When player is turned
back on later, playback will begin from
the bookmark.
*Player supports a single playback
bookmark.
Insert earphone or speaker plug into the
3.5mm stereo audio jack on the bottom
of the unit.
Press
or
to decrease or increase
volume. The volume will remain set at
this level even after the player is turned
off and restarted.
EARPHONES,
SPEAKERS AND
VOLUME
13
The Envoy 2 E/EZ can also play audio
from a properly formatted microSD card.
With the player facing you, insert the
card with the brass contacts showing
until it locks in place.
Once card is loaded, press
for 2
seconds repetitively until the player
beeps once. Playback will now begin
from the card.
USING THE
MICROSD CARD
14
To remove a card, gently push it in. The
reader will unlock and push it out so you
can remove it. If the player was in
playback mode from the card when
removed, it will beep once and revert to
the onboard memory. If any other
function was active, it will continue with
no change.
You can view, format and prepare an SD
card while loaded in the Envoy’s microSD
card reader when the player is
connected to a Computer using a USB to
micro-USB cable. You may also do the
same with the card loaded in a microSD
adaptor connected to a Computer.
See details on how to prepare the card
in the Envoy 2 E/EZ User Guide
document.
15
CHARGING
INSTRUCTIONS
With proper care, the Audio Player’s
Lithium-Ion battery should perform well
for several years. When shipped, the
battery is only partially charged. Please
fully charge the player before the first
use following one of the charging
methods below:
For fastest charge, connect any
standard “USB” charger (regulated
+5VDC, minimum 300mA) to the
micro-USB port on the bottom of the
player for about 2 hours or until the LED
stops blinking. While charging, the LED
will blink according to the charge level
(
Green
: 30-100%,
Yellow
: 10-29%,
Red
: 0-9%).
12
2/4