MegaPoints Controllers AutoSignal Скачать руководство пользователя

Страница: 15 / 16

MegaPoints Controllers AutoSignal User Guide

Revision 10

megapointscontrollers.co.uk

Page 15

Danger switch / sensor

Danger may be set by a toggle switch manually or automatically via an optional DCC block detector
or infra-red sensor (

analogue

). Danger is set when the SW terminal is shorted to ground.

When danger is released there is a 1 second delay.

Complimentary products

Use the following products to hook-up to your layout depending on your needs:

Product

Purpose

Part No

DCC Block Detector

Sense train occupancy on block

FB01-01

DCC Turnout Position Sensor

Determine points position on DCC
layouts

FB03-03

Block Detector (Infra-red)

Sense train position (analogue layout)

FB-01-01-1

Relay for AutoSignal

Switchable relay triggered on danger.
Use for stopping trains in front of
signals.

ASR01-01

DCC ABC Controller

Activates the ABC (Automatic Brake
Control) circuit on suitable equipped
locos. Requires the above Relay (ASR01-
01) to operate.

ABC01-01

Содержание AutoSignal

















Результаты поиска

Содержание AutoSignal

Отзывы:

Похожие инструкции для AutoSignal

Бренды по названию

Популярные бренды

MegaPoints Controllers AutoSignal, Руководство пользователя

Результаты поиска

Содержание AutoSignal

Отзывы:

Похожие инструкции для AutoSignal

Бренды по названию

Популярные бренды