manualshive.com logo in svg

Megaplot XMD Series, Руководство пользователя

Поделиться
Скачать
Megaplot XMD Series Скачать руководство пользователя страница 33

 page 33 of 73

•

move the spindle down very slowly until the tool reaches the table (make sure to do it 
very slowly to avoid breaking or damaging the tool

•

open Manual Control and Tool Length

•

press “Tool on table level” or “on material level”

•

move the spindle up

If the new tool is shorter than the previous one and you use the semi-automatic way to measure 

it, the spindle will not reach the table level as it is impossible to move the spindle into the negative 
co-ordinates. In this case, enter the 999 values as described above.

When the router is swiched off and back on again, the last tool measurement is remembered. If 

the tool has not been replaced in the meantime, there is no need to measure it again.

Cutting

Cutting

Before you start the cutting process, please double check all parameters in configuration, load 

the drawing and perform the simulation procedure. When you are ready to start, press START or F2. 

The spindle will first move to the project's starting position and then the spindle rotation will turn 

on. Spindle rotation and cutting speed may be adjusted during the cutting process.

You can stop the cutting process at any time by clicking STOP. If it is necessary to clean the tool, 

you   can   move   the   spindle   to   any   location   on   the   machine   and   once   the   tool   is   clean,   press 
CONTINUE or Shift +F2 and the router will move back to the location where the cutting process 
was stopped and will continue from this spot.

After   you   press   START  the   cutting   process  will   start   from   the   beginning   as  shown  on   the 

Simulation. However, it is possible to start the cutting from any given shape in the drawing. If 
needed, select a shape and click Cut \ 

Start from selected shape

.  You can also cut a single selected 

shape, if required.

Multi-layer drawings

Multi-layer drawings

When using multi-layer drawings, it is possible to engrave and cut from a single operation. In 

this case, the drawing will consist of a number of colors and for each color the operator can select 
the required cutting depth.

www.megaplot.com

 phone: +48 693 707 575  

[email protected]

Содержание XMD Series










































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды