manualshive.com logo in svg

Mega MMP4, Руководство по обслуживанию

Поделиться
Скачать
Mega MMP4 Скачать руководство пользователя страница 40

9-1

MMP4-CAT(T4)-MX-2

26 Feb 2014

SECTION 9

Special Inspections

Contents

DESCRIPTION

This section contains special inspection requirements
for a specific system after use, an unusual event or
storage.

STORAGE/WINTERIZATION

ENTERING

1. Remove any exterior dirt, grease and grime that

may trap moisture. 

2. Flush all water suction and discharge tubes (e.g.

water pump,).

3. Ensure all water is drained from the tubes and

water pump.

4. Ensure all covers/caps for fluid reservoirs are in

proper operating condition and are secured to
the openings. 

5. Fill Fuel tank to capacity, close fuel shut off valves

at bottom of fuel tank.

6. Check tires for proper inflation. 

7. Check Boom retaining hardware, ensure it is

operational and secure. 

8. Lubricate all grease points (e.g. Hinge pins,

cylinder pins, water pump suction bowl).

9. Check battery fluid level and charge.

10. Disconnect battery cables from battery.

11. Service all engine systems per CAT C2.2T Diesel

engine service manual (SEBU8312-02).

12. If possible, shelter entire unit from the elements.

REMOVING

1. Remove all covers and seals from all fill/discharge

openings and components.

2. Inspect piping for debris that may damage unit

that water will be pumped into.

3. Check to ensure all water pump reservoirs are

filled to the correct level and the fluid is not
contaminated. 

4. Remove any exterior dirt, grease and grime and

treat any corrosion. 

5. Service all Engine systems per CAT C2.2T Diesel

engine service manual (SEBU8312-02).

6. Check all fluid levels for condition and level,

replace or adjust as necessary.

7. Check Braking system (if equipped) repair as

necessary.

8. Check safety chains for damage.

9. Check lighting system for proper operation,

repair as necessary.

10. Clean and connect battery cables to battery.

11. Perform all ‘Daily’ maintenance checks, repair as

necessary.

12. Perform a full functional check of all MMP4

control systems.

Description .........................................................................9-1

Storage/Winterization....................................................9-1

Содержание MMP4

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды