Mega MMP4 Скачать руководство пользователя страница 29

Страница: 29 / 96

MMP4-CAT(T4)-MX-2

26 Feb 2014

SECTION 6

Axle and Suspension

6-2

9. Continue to pump grease until clean grease is

extruded through the outer bearing.

10. Rotate wheel while pumping grease into fitting.

11. Clean old grease from around the bearing cap.

12. Install the rubber plug in the grease cap.

13. Repeat on the other wheel bearing.

Manual wheel bearing greasing is only a semi-
annual service point. Failure to perform annual
wheel bearing service and inspection may result
in damage to the axle, wheel bearings or MMP4 if
not preformed.

INSPECTION

1. Inspect axle for cracking, damage and security.

2. Inspect springs for worn eye bushings, bent,

loose or broken shackles, mounts and bolts,
sagging or broken leafs, loose or damaged U-
bolts.

3. Check for loose wheel bearings.

4. Inspect lug nuts to ensure all are present and

torque properly to 80 to 90 ft/lbs (110 to 125 Nm).

5. Inspect for wheel seal leakage.

6. Inspect tires for inflation to 80 psi (550 kpa),

cracking, uneven wear, tread and side wall
damage.

7. Inspect fender assembly for security and damage

REPAIR

1. Axle tube, replace as required.

2. Damaged springs or mounting hardware, replace

as required.

3. Worn spring eye bushings, loose spring bolts and

damaged or worn shackles, replace as required.

4. Fender damage, repair as required.

5. Tire for wear or damage, replace as required.

6. Wheel bearings:

a. Secure MMP4 with jack stands and wheel

chocks.

b. Jack up 1 tire and secure axle.
c. Remove tire and rim assembly.
d. Remove wheel bearing grease cap.
e. Remove cotter pin or bend clear the nut

locking tab.

Remove spindle nut by turning nut CCW.

g. Remove hub assembly.
h. Inspect hub for damaged threads, missing or

damaged studs. Replace as required.

Inspect grease seal for damage (e.g; tears,
cracks, leaks and distortion).

To remove grease seal; pry out of hub with a
long handled screwdriver.

k. Clean and inspect wheel bearings and

bearing races for corrosion, pitting, wear, heat
discoloration and free/smooth movement.
Replace as required.

Never spin the wheel bearing with
compressed air. The bearing may be
damaged, causing the bearing explode
causing severe personal injury or death.

Nut Locking Tab

Содержание MMP4

































































































Результаты поиска

Содержание MMP4

Отзывы:

Похожие инструкции для MMP4

Бренды по названию

Популярные бренды

Mega MMP4, Руководство по обслуживанию

Результаты поиска

Содержание MMP4

Отзывы:

Похожие инструкции для MMP4

Бренды по названию

Популярные бренды