25
Supply descaling liquid
The dosing of the anti-limescale liquid inside the circuit is
activated only during hot machine operation and in case of
lack of anti-limescale liquid it switches off the hot operation.
Use protective gloves when filling the anti-scale
product canister.
Fill the anti-limescale canister as follows:
Turn OFF the machine and open the cover.
Fill the descaling tank with 1 liter of descaling product.
Only
use
descaler
recommended
by
the
manufacturer.
The dosing of the product is automatic and the
setting must be done by qualified technicians.
Starting the machine
Check that the main switch is in the OFF position (0)
Connect the water supply hose to the quick coupling water
inlet of the unit.
Connect the high pressure hose to the outlet of the pump
(OUTLET). The connection of high-pressure hose is pushed
to the end and then screwed by hand without the aid of
tools.
Connect the high pressure hose to the gun using tool.
(Fig.6)
Open the water supply tap completely
Insert the lance to the spray - gun
Insert the nozzle to the outlet of the lance by applying
Teflon and tightening with tool. (Fig.7).
Put the plug in the socket.
For the first start or after a long period of inactivity
it is necessary to connect for a few minutes only the
suction pipe and the water and keep disconnected high
pressure hose and gun to let out from the discharge any
impurities deposited inside the circuit. In this way you avoid
clog the nozzle of the gun.
Use
Whenever you use the 'high-pressure cleaner is
recommended to hold the gun in the right position,
with one hand on the handle and the other on the lance.
Use individual protective equipment during normal
use
To start the machine set the main switch to (I) and
pull the trigger of the gun.
When stopping and leaving the gun, activate the
safety lever.
Washing with hot water
Turn the switch for hot water to position 1
Set the water temperature by turning the knob of
temperature regulation.
The boiler will start the instantaneous heating
of the water with the operating status
indicator light and indicating the water outlet
temperature on the display. The heating stops and
turns on again automatically during normal use.
TOTAL STOP SYSTEM (Standard)
When the trigger gun
in relased the automatic pistol stops the pressure to
the nozzle and starts the water pump by-pass.
Automatically the heating stop burner is shut down
after programmable timing (Standard 20sec); the
reopening of the trigger gun makes the water pump to
restart pressure and the burner restarts automatically.
Pressure/flow rate regulation
Adjust the operating pressure by turning the knob
clockwise
to
increase
the
pressure
or
counterclockwise to decrease.
A decrease in pressure/flow allows higher
operating temperaturers of the water.
Washing with detergents in high pressure
High pressure detergent suction is carried out by
means of the water pump suction and only if the
appliance is equipped with a water filling tank with
float switch operation.
The detergent is sucked in by opening and adjusting
the detergent regulator tap on the control panel.
Содержание ASTRA EL18 140.10
