Mech Marvels MM2000DFI Скачать руководство пользователя страница 30

NEED HELP:1-800-832-2966

 

30 

 

As the power equipment engine owner, you should however be aware that QJ NORTH AMERICA INC. may deny 

your  warranty  coverage  if  your  power  equipment  engine  or  a  part  has  failed  due  to  abuse,  neglect,  improper 

maintenance or unapproved modifications. 

You are responsible for presenting your power equipment engine to distribution center or service center 

authorized by QJ NORTH AMERICA INC. as soon as the problem exists. The warranty repairs should be 

completed in a reasonable amount of time, not to exceed 30 day. 
If you have any questions regarding your warranty rights and responsibilities, you should contact QJ NORTH 
AMERICA INC. customer service representative at 1-800-832-2966 or write to 

[email protected].

 

DEFECTS WARRANTY COVERAGE 

Adopted by the Air Resources Board, QJ NORTH AMERICA INC. warrants to the ultimate purchaser and each 

subsequent purchaser that the small off-road engine (SORE)(1) has been designed, built and equipped so as to 

conform with all applicable regulations; and (2) is free from defects in materials and workmanship that cause the 

failure of a warranted part to conform with those regulations as may be applicable to the terms and conditions 

stated below. 

(a) The warranty period begins on the date the engine is delivered to an ultimate purchaser or first placed into 

service. The warranty period is two years. 

(b) Subject to certain conditions and exclusions as stated below, the warranty on emissions related parts is as 

follows: 
Any warranted part that is not scheduled for replacement as required maintenance in your Owner’s Manual is 
warranted for the warranty period stated above. If the part fails during the period of warranty coverage, the part: 

(1) 

will be repaired or replaced by QJ NORTH AMERICA INC. According to Subsection (4)  below. Any such part 

repaired or replaced under warranty will be warranted for the remainder of the periods.

 

(2) 

Any warranted part that is scheduled only for regular inspection in your owner’s manual is warranted for the 

warranty period stated above. Any such part repaired or replaced under warranty will be warranted for the remaining 

warranty period.

 

(3) 

Any  warranted  part  that  is  scheduled  for  replacement  as  required  maintenance  in  your  owner’s  manual  is 

warranted for the period of time before the first scheduled replacement date for that part. If the part fails before the 

first  scheduled  replacement,  the  part  will  be  repaired  or  replaced  by  QJ  NORTH  AMERICA  INC.  According  to 

Subsection (4) below. Any such part repaired or replaced under warranty will be warranted for the remainder of the 

period prior to the first scheduled replacement point for the part.

 

(4) 

Repair  or  replacement  of  any  warranted  part  under  the  warranty  provisions  herein  must  be  performed  at  a 

warranty station at no charge to the owner.

 

(5) 

Notwithstanding  the  provisions  herein,  warranty  services  or  repair  will  be  provided  at  all  of  our  distribution 

centers that are franchised to service the subject engines.

 

(6) 

The engine owner must not be charged for diagnostic labor that leads to the determination that a warranted part 

is in fact defective, provided that such diagnostic work is performed at a warranty station.

 

(7) 

QJ NORTH AMERICA INC. is liable for damages to other engine components proximately caused by a failure 

under warranty of any warranted part.

 

(8) 

Throughout  the  engine  warranty  period  stated  above,  QJ  NORTH  AMERICA  INC.  will  maintain  a  supply  of 

warranted part sufficient to meet the expected demand for such parts.

 

(9) 

Any replacement may be used in the performance of any warranty maintenance or repairs and must be provided 

without charge to the owner. Such use will not reduce the warranty obligations of QJ NORTH AMERICA INC.

 

(10) 

Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use 

of any non-exempted add-on or modified parts by the ultimate purchaser will be grounds for disallowing a warranty 

claims. QJ NORTH AMERICA INC. will not be liable to warrant failures of warranted parts caused by the use of a 

non-exempted add-on or modified part.

 

(11) 

The manufacturer issuing the warranty shall provide any documents that describe that manufacturer’s 

warranty procedures or policies within five working days of request by the Air Resources Board.

 

Содержание MM2000DFI
































Отзывы: