Mec 500E DOUBLES ATA Скачать руководство пользователя страница 16

Страница: 16 / 19

Page 16 Rev. 1

FAULT FINDING ELECTRICAL

CAUTION: ANY MEC MACHINE MUST BE IN THE DISARMED STATE WITH THE BATTERY
DISCONNECTED PRIOR TO MAKING ANY ADJUSTMENTS, LOADING WITH CLAYS OR
TRANSPORTING

1. Machine does not Arm

Check:

(a)

Battery is charged and that connections are tight.

(b)

Toggle switch is in the down ON position or on the Handheld that the “ARM” indicator light is on.

(c)

There are 3 components in place to protect your electrical box.

1. Re-settable breaker. Found on the side of the electrical box. (older models have non-resettable breakers)

2. 60amp or 70amp relay. Found inside the electrical box. (automotive type)

3. Inline fuse. Found inside electrical box. (7.5amp automotive type 2 prong fuse)

https://www.youtube.com/watch?v=JZZmYQtybAE

replacing fuse

Содержание 500E DOUBLES ATA




















Результаты поиска

Содержание 500E DOUBLES ATA

Отзывы:

Похожие инструкции для 500E DOUBLES ATA

Бренды по названию

Популярные бренды

Mec 500E DOUBLES ATA, Руководство пользователя

Результаты поиска

Содержание 500E DOUBLES ATA

Отзывы:

Похожие инструкции для 500E DOUBLES ATA

Бренды по названию

Популярные бренды