Mec 500E DOUBLES ATA Скачать руководство пользователя страница 12

 

 

 

Page 12                                                                                                                                    Rev. 1 

 

Step 19

 

– Press the fire button on the pull cord or wireless release.  This will cause the machine to 

fire a clay target and then reset to the firing position.  Pressing the fire button again will do the same 
as above.  Pressing and holding the fire button will continuously fire clays continuously 
 
Your machine is now operating smoothly and ready for use.  

It is critical that you never load or 

make adjustment to the machine unless it is disarmed and the power disconnected.  

While in 

storage, the machine must be left in the disarmed state and the power/battery disconnected.   Any 
spring tension does not need to be released. 
 
 
Your machine is now operating smoothly and ready for use.  It is critical that you never load or make 
adjustment to the machine unless it is disarmed, and the battery disconnected.  While in storage, the 
machine must be left in the disarmed state and the battery disconnected.   Any spring tension does 
not need to be released. 
 
Thanks for choosing MEC!  Every machine is hand set and tested prior to leaving our shop to ensure 
quality.  We take pride in our products, so you can have a better experience in the field.  Your 
patronage is very much appreciated! 
 
For any questions regarding setup or use of any MEC Clay Target Machines, please feel free to call 
our toll free number listed below, or visit us on the web to watch our setup and demonstration videos. 
 
 
 

                                            For all ATA rules and guidelines please see the link below.

 

https://www.shootata.com/Portals/0/pdf/ata_rulebook_web.pdf

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание 500E DOUBLES ATA




















Отзывы: