Mec 1330SE Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 84

Mec 1330SE Скачать руководство пользователя страница 22

Page 18

1330SE - Servce & Parts Manual

November 2021

Secton 10 - Mantenance

Check each battery pack and verify that the batteries
are wired correctly.
Inspect the battery charger plug and pigtail for damage
or excessive insulation wear. Replace as required.
Connect the battery charger to a properly grounded
110 - 230V / 50 - 60 Hz single phase AC power supply.

6.

7.

8.

ART_5050

Batteries

Power

Switch

150A Fuse

Battery

Charger

Result:

The charger should operate and begin charging the batteries.

Result:

If, simultaneously, the charger alarm sounds and the LEDs blink, correct the charger

connections at the fuse and battery. The charger will then operate correctly and begin charging
the batteries.

•
•

Note: For best results, use an extension cord of adequate size with a length no longer than 50

ft / 15 m.

If you have any further questions regarding the battery charger operation, please
contact the MEC Customer Service.

Electrical Wiring

Maintaining electrical wiring in good condition is essential to safe operation and good machine
performance. Failure to find and replace burnt, chafed, corroded or pinched wires could result in
unsafe operating conditions and may cause component damage.

ELECTROCUTION / BURN HAZARD. CONTACT WITH ELECTRICALLY
CHARGED CIRCUITS COULD RESULT IN DEATH OR SERIOUS INJURY.

REMOVE ALL RINGS, WATCHES AND OTHER JEWELRY.

Inspect the following areas for burnt, chafed, corroded and loose wires:

Ground control panel
Hydraulic power unit module tray
Platform controls

Turn the key switch to ground control and turn the red Emergency Stop button clockwise to the
“ON” position at both the ground and platform controls
Raise the platform approximately 7.2 ft / 2.2 m from the ground.
Lift the safety arm, move it to the center of the scissor arm and rotate up to a vertical position.
Lower the platform onto the safety arm.

CRUSHING HAZARD. KEEP HANDS CLEAR OF THE SAFETY ARM WHEN
LOWERING THE PLATFORM.

Inspect the center chassis area and scissor arms for burnt, chafed and pinched cables.
Inspect the following areas for burnt, chafed, corroded, pinched and loose wires:

1.

•
•
•

1.

2.
3.
4.

6.
7.

«
...
20
21
22
23
24
...
»

Содержание 1330SE





















































































Отзывы:

Нет отзывов