manualshive.com logo in svg

Measurement Computing PCI-DAS6030, Руководство пользователя, Страница: 35 / 50

Поделиться
Скачать
Measurement Computing PCI-DAS6030 Скачать руководство пользователя страница 35

34 

Chapter 5 

Specifications 

All specifications are subject to change without notice. 
Typical for 25 °C unless otherwise specified.  
Specifications in 

italic text

 are guaranteed by design. 

Analog Input 

Table 1. Analog input specifications 

Parameter 

Specification 

A/D converter  

Successive approximation type 

Resolution 

16 bits, 1 in 65536 

Maximum sample rate 

100 kS/s  

Number of channels 

16 single ended / 8 differential, software selectable 

Input ranges  

Bipolar:  

±10 V, ±5 V, ±2 V, ±1 V, ±0.5 V, ±0.2 V, ±0.1 V  

Unipolar:  

0 to 10 V, 0 to 5 V, 0 to 2 V, 0 to 1 V, 0 to 0.5 V, 0 to 0.2 V,  
0 to 0.1 V 

Software selectable 

A/D pacing 
 

Internal counter – ASIC. Software selectable time base: 

 

Internal 40 MHz, 50 ppm stability 

 

External source via AUXIN<5:0>, Software selectable. 

External convert strobe: A/D CONVERT 

Software paced 

Burst mode 

Software selectable option, burst rate = 10 µS.  

A/D gate sources 

External digital:   A/D GATE 

External analog:   ATRIG input 
 

CH0 IN through CH15 IN 

A/D gating modes 

External digital:   Programmable, active high or active low, level or edge 

External analog:   Refer to 

Analog Trigger

 on page 39. 

A/D trigger sources 
 

External digital:  A/D START TRIGGER 

A/D STOP TRIGGER 

External analog:   ATRIG input 

CH0 IN through CH15 IN 

A/D triggering modes 

External digital:   Software-configurable for rising or falling edge. 

External analog:   Refer to 

Analog Trigger

 on page 39. 

Pre-/Post-trigger: Unlimited number of pre-trigger samples, 16 Meg post-trigger samples.  

ADC pacer out 

Available at user connector: A/D PACER OUT 

RAM buffer size 

8 K samples 

Data transfer 

DMA  

Programmed I/O 

DMA modes 

Demand or Non-demand using scatter-gather. 

Configuration memory  

Up to 8 K elements. Programmable channel, gain, and offset. 

Streaming-to-disk rate 

100 kS/s, system dependent 

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание PCI-DAS6030



















































Отзывы:

Нет отзывов