background image

INSTALLATION

Communications between the main unit (receiver) and the remote sensor (transmitter) is 
wireless. This allows you to greater flexibility in choosing the location of remote sensor. The 
remote transmits data up to 164 feet (50 meters) over an open, unobstructed area.
The remote sensor can be located either indoors or outdoors, allowing you chose where your 
data is obtained.

NOTE:

• It is critical to power the remote sensor 

BEFORE

 setting up the main unit. 

• It is critical to power up and 

test

 communication between the remote sensor and the main unit 

BEFORE

 permanently mounting if outside. 

BEFORE YOU BEGIN

• We recommend using 

alkaline batteries

 for the remote sensor. If outdoor temperatures 

   regularly fall 

below 32°F 

(0°C), we recommend using lithium batteries.

• Avoid using rechargeable batteries. (Rechargeable batteries cannot maintain correct 
   power  requirements.)

ALWAYS

 install batteries in the remote sensor before the main unit.

• Insert batteries before first use, matching the polarity in the battery compartment.

• Press 

RESET

 after each battery change with a paper clip or similar tool.

• During initial set up, place the remote sensor close to the main unit. 

• After reception is established (remote readings will appear on the main unit’s display), 
  position the remote sensor and the main unit within the effective transmission range of up to 
  164 feet (50 meters).

• The main unit must be placed indoors.

NOTE:

• Avoid pressing any buttons on the main unit before the remote readings are displayed.

• Transmission or reception range may be affected by trees, metal structures, and electronic 
   appliances, surrounding building materials and how the main unit and transmitter are 
   positioned.

• Place the remote sensor so that it faces the main unit (receiver), minimizing obstructions such 
   as doors, walls and furniture.

• Though the remote sensors are weather-resistant, they should be placed away from direct 
   sunlight, rain or snow. The optimal location for the remote sensor outdoors is under the eaves 
   on the north side of the building.

3

MADE IN CHINA

Содержание TE653ELW-M

























Отзывы: