background image

24

McQuay IM 777-4

Service and Maintenance

LVP Variable Speed Sheaves

Mounting

1

Slide sheave on motor shaft so that the side of the sheave 

with setscrew 

A

 is next to the motor when setscrew 

A

 is 

in the hub or barrel of the sheave.

2

When setscrew 

A

 is at an angle in the center flange 

B

mount it away from the motor so that the outer locking 
ring and flange can be removed to get to the setscrew.

3

To remove the flange and locking ring:

a

Loosen setscrews 

D

.

b

Loosen but 

do not remove

 capscrews 

E

.

c

Remove key 

F

Note: 

This key projects a small amount to provide a grip for 

removing.

d

Rotate the flange counterclockwise until it disengages 
the threads on the sheave barrel.

4

Verify that the driving and driven sheaves are in 
alignment and the shafts are parallel. When aligning two-
groove sheaves, allow room between the sheave and 
motor to access capscrews 

E

.

5

Insert key 

C

 between the sheave and the shaft and tighten 

setscrew 

A

 securely.

6

If flange and locking ring have been removed, when 
replacing them make sure that the inner and outer flanges 
are open from the closed position by the same amount as 
the other flange. Determine this by accurately measuring 
the top width of the grooves.

7

Insert key 

F

.

8

Tighten setscrews 

D

 and capscrews 

E

.

9

Put on belts and adjust belt tension. 

Do not force belts 

over grooves. 

See 

Fan Drive Belt‚ page 26

.

10

Before starting the drive, ensure that all keys are in place 
and all setscrews and all capscrews are tight. Check and 
retighten all screws and retension belts after 
approximately 24 hours of service.

Adjusting

1

Slack off belt tension if belts have been installed.

2

Loosen setscrews 

D

.

3

Loosen but 

do not remove

 capscrews 

E

.

4

Remove key 

F

Note: 

This key projects a small amount to provide a grip for 

removing.

5

Adjust pitch diameter by opening or closing the movable 
flanges by half or full turns. 

Note: 

Two-groove sheaves are supplied with both grooves 

set at the same pitch diameter. 

6

To provide the same pitch diameter for satisfactory 
operation, move both movable flanges the same number 
of turns. Do not open sheaves more than five turns for 

A

 

belts or six turns for 

B

 belts.

7

Replace key 

F

.

8

Tighten setscrews 

D

 and capscrews 

E.

9

If belts have been installed, readjust belt tension. If belts 
have not been installed, install them and adjust belt 
tension. 

Do not force belts over grooves.

 

See 

Fan Drive 

Belt‚ page 26

.

10

Before starting the drive, ensure that all keys are in place 
and all setscrews and all capscrews are tight. Check and 
retighten all screws and retension belts after 
approximately 24 hours of operation.

Figure 36: LVP Type Sheave Adjustment

Section A-A

Section A-A

A

B

C

D

E

F

D

E

A

E

C

F

D

A

A

Содержание Skyline OAC 003





































Отзывы: