McQuay MQIU-174018-HCU216A Скачать руководство пользователя страница 9

Страница: 9 / 40

3.3

Introduction for buttons on remote controller

X-FAN button

Press this button under cool and dry mode to start up x-fan function, and " " icon

on remote controller will be displayed. Press this button again to cancel x-fan

function, and " "icon will disappear.

Note:

● When x-fan function is on, if the air conditioner is turned of

f, indoor fan will still

operate at low speed for a while to blow the residual water inside the air duct.

● During x-fan operation, press X-

FAN button to turn off x-fan function. Indoor fan

will stop operation immediately.

TURBO button

Under COOL or HEAT mode, press this button to turn to quick COOL or quick

HEAT mode. " " icon is displayed on remote controller. Press this button again

to exit turbo function and " " icon will disappear.

Press this button to turn off display light on indoor unit. " " icon on remote

controller disappears. Press this button again to turn on display light. " " icon is

displayed.

Under COOL, HEAT

or D

RY mode, press this button to start up sleep function.

" " icon is displayed on remote controller. Press this button again to cancel sleep

function and " " icon will disappear.

SLEEP button

LIGHT button

3.4

Function introduction for combination buttons

Child lock function

Press "+" and "-" simultaneously to turn on or turn of

f child lock function. When

child lock function is on, " " icon is displayed on remote controller. If you operate

the remote controller, the " " icon will blink three times without sending signal to

the unit.

Temperature display switchover function

Under OFF status, press "-" and "MODE" buttons simultaneously to switch temp-

erature display between

℃

and

℉

Содержание MQIU-174018-HCU216A









































Результаты поиска

Содержание MQIU-174018-HCU216A

Отзывы:

Похожие инструкции для MQIU-174018-HCU216A

Бренды по названию

Популярные бренды

McQuay MQIU-174018-HCU216A, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MQIU-174018-HCU216A

Отзывы:

Похожие инструкции для MQIU-174018-HCU216A

Бренды по названию

Популярные бренды