background image

26

Input Impedance

High Level - 20K ohms

Phono - 47K ohms; 50pF-800pF

Preamplifier Output 2 (for rated input)

1.4V unbalanced (8V Maximun)

Maximum Input Signal

High Level - 8V unbalanced, 16V balanced

Phono - 80mV

Voltage Gain

High Level to Output 1: 44dB

High Level to Output 2: 15dB

Phono to Output 1: 84dB

Phono to Output 2: 55dB

Headphone Impedance

100 to 600 ohms

Trigger Output

12VDC, 25mA

Equalizer Control

s

Amplifier Specifications

Power Output Stereo

Minimum sine wave continuous average power output per 

channel, with both channels operating is: 

200 watts into 8 ohm load

320 watts into 4 ohm load

Output Load Impedance

8 or 4 ohms 

Rated Power Band

20Hz to 20,000Hz

Total Harmonic Distortion

0.03% maximum with both channels operating from 250 

milliwatts to rated power, 20Hz to 20,000Hz

Intermodulation Distortion

0.03% maximum, if the instantaneous peak power output 

does not exceed twice the rated power output for any com-

bination of frequencies from 20Hz to 20,000Hz

Dynamic Headroom

1.5dB

Wide Band Damping Factor

Greater than 200 - 8 ohm, Greater than 100 - 4 ohm

Power Guard

Less than 2% THD with up to 16dB overdrive at 1,000Hz

Frequency Response

+0, -0.5dB from 20Hz to 20,000Hz

+0, -3dB from 10Hz to 100,000Hz

Preamplifier Output Impedance

500 ohms

Sensitivity (for rated output)

High Level - 250mV unbalanced, 500mV balanced

Phono - 2.5mV

Signal To Noise Ratio (A-Weighted)

High Level - 93dB below rated output

Phono - 82dB below 5mV input

Specifications

General Specifications

Power Requirements

Field AC Voltage conversion of the MA352 is not pos-

sible. The MA352 is factory configured for one of the 

following AC Voltages:

100 Volts, 50/60Hz at 7.2 amps

110 Volts, 50/60Hz at 6.0 amps

120 Volts, 50/60Hz at 6.0 amps

127 Volts, 50/60Hz at 6.0 amps

220 Volts, 50/60Hz at 3.3 amps

230 Volts, 50/60Hz at 3.3 amps

240 Volts, 50/60Hz at 3.3 amps

Standby: Less than 0.5 watt

Note: Refer to the rear panel of the MA352 for the cor-

rect voltage.

Overall Dimensions

Width is 17-1/2 inches (44.5cm)

Height is 9-7/8 inches (25.1cm) including feet

Depth is 20-1/2 inches (52.1cm) including the Cables

Weight

66 pounds (29.9 kg) net, 75 pounds (34.0 kg) in shipping 

carton

Shipping Carton Dimensions

Width is 22-5/8 inches (57.5cm)

Depth is 21-7/8 inches (55.6cm) 

Height is 12-7/8 inches (32.7cm

)

 

-15

20                50           100          200              500           1k    

        2k               5k          10k        20k

FREQUENCY IN HERTZ

   0

 

-  5

A

M

P

L

I

T

U

D

E

I

N

D

E

C

I

B

E

L

S

 

-10

 

+  5

 

+10

 

+15

Содержание MA352





























Отзывы: