McIntosh LCR80, Руководство пользователя

Страница: 8 / 16

8
2. If the LCR80 is to be mounted in a horizontal
position proceed to step 3. When the LCR80 is to
be mounted in a vertical position, it is important
to rotate the Midrange/Tweeter Mounting Plate to
provide the optimum sound image. This is accom-
plished by the following steps:
A. Place the LCR80 on a flat surface with the
Loudspeaker Drivers facing up.
B. Temporarily
remove the
four screws
securing the
Midrange/
Tweeter Met-
al Mounting
Plate. Refer
to figure 6B.
C. Carefully lift up the metal mount-
ing plate to clear the cabinet
opening. Rotate it 90 degrees from
the current orientation and then
reinsert it back into the cabinet.
Refer to figure 6C.
D. Secure the metal mounting plate to
the cabinet using the four previous
removed mounting screws.
3. Attach either the flush mount or angle mount
brackets to the rear of the Loudspeaker. Refer to
the chart below, along with figures 5 and 7 for the
screw location. Also, be sure to orient the bracket
as illustrated in figures 8 and 9.
Note: The Angled Bracket is only for vertical
mounting of the LCR80 Loudspeaker.
4. Determine the Loudspeaker Mounting Location
on the wall, making sure the Mounting Bracket
will be anchored to a stud located inside the wall.
Note: Use extreme caution to avoid any existing
electrical wiring, plumbing, etc., located
inside the wall.
5. Refer to figures 10 thru 15 to install the appropri-
ate Wall Bracket on the wall (orient the bracket as
illustrated) using the supplied Mounting Screws.
If the Flush Mount Bracket is used, attach the two
rubber bumpers to the rear of the Loudspeaker,
near the bottom.
Note: If the wall covering material and/or thick-
ness is different from the illustration, the
two supplied Mounting Screws need to be
replaced with screws of the appropriate type
and length.
6. Orient the Loudspeaker to line up with the Wall
Brackets and attach them together. If the angle
mount is used, install the Locking Screw to secure
the Loudspeaker at the desired angle.
7. The LCR80 Loudspeaker Grille is secured to the
Loudspeaker Cabinet with magnetic fasteners.
Locate the Loudspeaker Grille and align it with
the edges of the cabinet.
Note: Retain the shipping carton, foam packing ma-
terial and fiber cover for possible future use.
8. Optionally, attach the supplied McIntosh Logo to
the Front of the LCR80 Loudspeaker Grille in the
desired location.
9. Proceed to “Room Acoustics and Loudspeaker
Placement” on page 10.
The supplied On Wall Mounting Brackets allow for
different mounting positions of the LCR80 Loud-
speaker relative to the wall, both vertical and horizon-
tal. Two positions are flush mount, with the Loud-
speaker close to and parallel with the wall. The other
position is angle mount, which places the Loudspeaker
further away from the wall and allows for rotation of
±30 degrees. Refer to figure 5.
1. Using an appropriate tool, remove the screws
securing the Rear Stabilizers to the back of the
LCR80. Refer to figure 6A.
Note: Retain the removed screws and Rear Stabi-
lizer for possible future use.
Installing the LCR80 on the Wall
Figure 5
Loudspeaker Bracket
Locking
Screw
Wall Bracket
Horizontal Wall Mounting
Angled Hardware
Vertical and Horizontal
Wall Mounting
Flush Hardware
Wall Bracket
Loudspeaker Bracket
Wall
Mounting
Screws
Figure 6A
Stabilizer Bar Screws
Rear Stabilizers
Figure 7
Screws - H Screws - H
Screws - V Screws - V
Location R
Location L
Figure 6B
Midrange/Tweeter Metal Mounting Plate
Screws Screws
Figure 6C