background image

3

Needlenose Pliers

PH 2

95 or Higher 

Octane Gasoline 

2 Stroke Oil

(High Quality racing 

oil recommended)

Cutter

Divider

Caliper

Engine

Receiver

Battery extension wire

At least 4 Servos

(Minimum capacity: 15kg for

steering, 15kg for throttle and

brake)

Or

Needed Equipment

Transmitter

Sizes: 5.5mm, 7mm, 9mm, 13mm 

Sizes: 1.5mm, 2mm, 2.5mm, 3mm, 4mm

Wrench 

Hex Driver

NiMH Battery

(Max dimensions: 

127mm x 57mm x h:39mm)

Battery Charger

Li-PO/LiFE Battery

(Max dimensions: 

127mm x 57mm x h:39mm)

 Screwdriver

Air Filter Oil

Thread Lock

Shock Oil

(standart 1000cSt)

Brake Fluid

(silicone dot 5)

Hydraulic Oil 32

inside the Diff

Body Reamer

Make sure your car is properly maintained before you start running!

Check all screws and nuts for a proper and firm seat. Use thread lock, where screws thread into metal.
Never drive without fully charging batteries for the transmitter and receiver against the risk of a runaway.
Always check the brake and throttle linkage before you start the engine.
Be sure the air filter is clean and properly oiled. Never run the engine without an air filter as dust 
and debris may enter inside and seriously damage the engine.

Always be sure that nobody else uses the same frequency.

Always be sure that there is grease inside the cup joint boots.

Operation

Exhaust fumes are poisonous. Never operate the engine in closed spaces.
Break-in procedure should be payed attention.
Be sure the air filter is clean and well-oiled. Never operate the engine without an air filter attached.

Use minimum 95 Octane gasoline mixed with high quality two-cycle engine oil. 
Use a 20:1 ratio gasoline to oil. (e.g. 

250ml oil mixed with 5lt Fuel

Use original engine spare parts only.

Check the air filter regularly for eventual damages.

The Do’s

The Dont’s

Switch on the transmitter before starting the 

engine.

Never run with low batteries.

Drive carefully when there are people around.

Never run your car in wet conditions or on tall grass. 

Switch engine off first, and then the transmitter. 

Never use chemicals for cleaning your car.

Always check the condition of the batteries before

running the engine.

Never run your car without the bodyshell.

Содержание duox













Отзывы: