McCulloch 250CXL Скачать руководство пользователя

Страница: 12 / 16

Button

Air Filter Cover

Air Filter

REPLACE SPARK PLUG

Replace the spark plug each year to ensure

the engine starts easier and runs better. Set

spark plug gap at 0,6 mm. Ignition timing is

fixed and nonadjustable.

1. Twist, then pull off spark plug boot.

2. Remove spark plug from cylinder and dis-

card.

3. Replace with Champion RCJ-6Y spark

plug and tighten securely with a 19 mm

socket wrench.

4. Reinstall the spark plug boot.

SERVICE AND ADJUSTMENTS

REPLACING THE LINE

1. Press the tabs on the side of the trimmer

head and remove cover and spool.

Tab

Cover

Tap Button

2. Remove any remaining line.

3. Clean dirt and debris from all parts. Re-

place spool if it is worn or damaged.

4. Replace with a pre-wound spool, or re-

place line using a 8 meters length of 2 mm

diameter McCulloch brand line.

5. When installing new line on an existing

spool, hold the spool as shown in the il-

lustration below.

6. Bend the line at the midpoint and insert

the bend into the slot in the center rim of

the spool. Ensure line snaps into position

in the slot.

Slot

Spool

7. With your finger between the lines, wrap

the lines evenly and firmly around the

spool in a clockwise direction.

8. Position the lines in the guide slots.

Guide

Slot

Guide Slot

9. Insert the ends of the lines through exit

holes in the sides of the cover.

10. Place the spool in the cover.

Spool

Cover

11. Make sure the lines are not caught be-

tween the rim of the spool and the wall of

the cover.

12. Reinstall the spool and cover onto the trim-

mer head. Push until cover snaps into

place.

CARBURETOR ADJUSTMENT

WARNING:

Keep others away when

making idle speed adjustments. The trimmer

head will be spinning during most of this pro-

cedure. Wear your protective equipment and

observe all safety precautions. After making

adjustments, the trimmer head must not

move/spin at idle speed.

The carburetor has been carefully set at the

factory. Adjustments may be necessary if you

notice any of the following conditions:

Engine will not idle when the throttle is re-

leased.

The trimmer head moves/spins at idle speed.

Содержание 250CXL

















Результаты поиска

Содержание 250CXL

Отзывы:

Похожие инструкции для 250CXL

Бренды по названию

Популярные бренды

McCulloch 250CXL, Инструкция по эксплуатации

Результаты поиска

Содержание 250CXL

Отзывы:

Похожие инструкции для 250CXL

Бренды по названию

Популярные бренды