McCrometer FlowConnect Скачать руководство пользователя страница 8

Страница: 8 / 19

published technical data and instructions are subject to change without notice. Contact your McCrometer representative for current

technical data and instructions.

www.mccrometer.com

3255 WEST STETSON AVENUE • HEMET, CALIFORNIA 92545 USA

TEL: 951-652-6811 • 800-220-2279 • FAX: 951-652-3078 Printed In The U.S.A. Lit. # 30122-40 Rev. 1.0 / 3-1-17

Page 8 of 19

™

FlowConnect

Figure 3. Attaching the

cellular antenna

Figure 4. Attaching the

antenna extension

STEP 9: Attach the antenna

Figure 5. Attaching the

cellular antenna

Figure 6. Attaching the

satellite antenna

Attach the cellular antenna or antenna extension by screwing it to the antenna post.

Figure 7. Attaching the

antenna extension

Figure 8. Non-rechargeable

batteries

Figure 9. Rechargeable batteries

a. Remove the battery cover.

b. Ensure the batteries are in place

and plug the leads into the

connectors in the order shown in

Figure 8 and Figure 9.

STEP 10: Connect the batteries and attach the battery cover
Connecting the batteries for both non-rechargeable and rechargeable types is identical.

Firs

First

Sec

ond

Sec

ond

c. Replace the battery cover, making

sure the O-ring is set in place flat

and even, without any twisting.

d. Set the cover in position over the

battery compartment. It will set

easily in place. Tighten the four

screws snug and hand tight.

The antenna MUST be attached before the batteries are inserted! Powering up the unit without the

antenna may damage the modem!

Содержание FlowConnect




















Результаты поиска

Содержание FlowConnect

Отзывы:

Бренды по названию

Популярные бренды

McCrometer FlowConnect, Инструкция по модернизации

Результаты поиска

Содержание FlowConnect

Отзывы:

Бренды по названию

Популярные бренды