MC Electronics MCK 2500 SX Скачать руководство пользователя | Manualshive

Страница: 37 / 48

background image

Installation and use

37

SEEDER MAT MCK 2500 SX

= RPM distributor alarm

= RPM turbine alarm

!

NOTE:

The self-acquisition procedure must only be carried out the first time the
seeder is used. Afterwards, the computer keeps the rotation and alarm
thresholds memorized, even if the battery is disconnected.

5.9 Checking speed sensor operation

Check the speed inductive sensor as follows:

1. Turn on the computer (

ON

OFF

key);

2. repeatedly press the

M.

key until the indication, “Km/h”, appears on the

right side of the display.

3. Using a screwdriver, or another metallic mass, pass it repeatedly in front of the

red part of the sensor. If on the computer display the simulated speed indication
appears (which will probably not be constant), this means that the sensor is
properly working and correctly connected.

5.10 Checking turbine RPM sensor operation

Check the RPM speed as follows:

1. Turn on the computer (< ON/OFF> key);

2. repeatedly press the

M.

key until the indication, RPM, appears on the

right side of the display.

3. Using a screwdriver, or another metallic mass, pass it repeatedly in front of the

red part of the sensor. If on the computer display the simulated RPM indication

«
...
35
36
37
38
39
...
»

Содержание MCK 2500 SX

















































Отзывы:

Нет отзывов

Похожие инструкции для MCK 2500 SX

Thiele Technologies Streamfeeder Reliant...

Бренд: Barry-Wehmiller Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды