Version 02/12
LED Effect Beamer GST-104B
Item no. 59 15 28
Intended use
1.
The product is intended to provide a colourful light projection with the sound triggering
function. The built-in LEDs create constantly changing light patterns. The product is
powered by 110 - 240 V/AC, 50/60 Hz. Use only in dry indoor environment.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If
you use the product for purposes other than those described above, the product may be
damaged. In addition, improper use can cause hazards such as short circuiting, fire, electric
shock etc. Read the instructions carefully and keep them. Make this product available to
third parties only together with its operating instructions.
Delivery content
2.
LED effect beamer
•
Power supply unit
•
Hexagonal wrench
•
Operating instructions
•
Safety instructions
3.
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
Persons / Product
The device is not a toy. Keep it out of the reach of children and pets.
•
Do not leave packaging material lying around carelessly. These may become dangerous
•
playing material for children.
Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
•
moisture, flammable gases, vapours and solvents.
Do not place the product under any mechanical stress.
•
If it is no longer possible to operate the product safely, take it out of operation and protect
•
it from any accidental use. Safe operation can no longer be guaranteed if the product:
is visibly damaged,
-
is no longer working properly,
-
has been stored for extended periods in poor ambient conditions or
-
has been subjected to any serious transport-related stresses.
-
Please handle the product carefully. Jolts, impacts or a fall even from a low height can
•
damage the product.
Also observe the safety and operating instructions of any other devices which are
•
connected to the product.
Never look directly or with optical instruments into the light beam.
•
Do not point the light beam at mirrors or other reflective surfaces.
•
Never point the light beam directly at people or animals. This could cause damage to
•
eyes or skin.
Point the light beam in such a way that it is directed below eye level.
•
Miscellaneous
Consult an expert when in doubt about operation, safety or connection of the device.
•
Maintenance, modifications and repairs are to be performed exclusively by an expert or
•
at a qualified shop.
If you have questions which remain unanswered by these operating instructions, contact
•
our technical support service or other technical personnel.
Mounting
4.
The mounting bracket is set up so you can mount the beamer on the ceiling, a wall or any
rigid surface. Mount it according to your requirements. However, this is optional and does
not affect the lighting function of the beamer.
Prepare a drill (not included) with a drill bit of suitable size..
1.
Mark the place where you want to install the beamer. Make sure the power cable of the
2.
product can reach a mains outlet.
Drill into the surface where you are going to mount the beamer.
3.
When drilling mounting holes or screwing down, ensure that no existing
electrical cables, gas or water pipes will be damaged.
Unscrew the screws on the left and right side of the bracket with the L wrench. Remove
4.
the beamer from the bracket.
Fix the bracket with a screw on the surface. Use the washers (not included), plastic
5.
expansion plugs (not included) or plastic screw anchors (not included) if necessary.
Fasten the beamer on the bracket again.
6.
Operation
5.
If you need to adjust the beaming angle, loose the screws on the left and right side of the
1.
bracket with the L wrench. Adjust the angle and then tighten the screws again. Place it on
a flat, stable surface or mount it on a rigid surface. (See the chapter “Mounting”)
Connect the hollow power plug on the power supply unit to the power inlet at the back
2.
of the beamer.
Connect the power supply unit to a main outlet.
3.
Press the ON / OFF button to switch the product on / off.
4.
Press the sound activation button to switch the sound activation function on / off. If
5.
the function is switched on, the beamer will adapt its light pattern to follow the sound
rhythm.
Turn the knob to change the speed at which the pattern moves.
6.
Disposal
6.
In order to preserve, protect and improve the quality of environment, protect
human health and utilise natural resources prudently and rationally, the user
should return unserviceable product to relevant facilities in accordance with
statutory regulations.
The crossed-out wheeled bin indicates the product needs to be disposed
separately and not as municipal waste.
Technical data
7.
Operating voltage:
5 V/DC
Output power:
1 W
Operating temperature:
-10 to +45 ºC
Operating humidity:
0 – 80 % RH
Dimensions (ø x L):
85 x 156 mm
Weight:
235 g
Power supply unit
Input voltage:
110 – 240 V/AC, 50/60 Hz
Output voltage:
5 V
Output current:
max. 1 A
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
© 2012 by Conrad Electronic SE.
V1_0212_02-HL
