background image

- 4 -

O

PERATION

Introduction

MBW equipment is intended for use in very severe
applications.  They are powered by four cycle engines and
are available in different sizes and a selection of engines.

This parts manual contains only standard parts.  Variations
of these parts as well as other special parts are not included.
Contact your local MBW distributor for assistance in
identifying parts not included in this manual.

The MBW 1400 & 1800 compactors are intended to
compact various types of soil. Recommended soil types
include granular soils and gravel & sand mixtures. These
compactors are not intended to be used on cohesive soils
such as clay or hard surfaces like concrete.

Before Starting & Operating

• 1400 Series Handle installation.

Refer to HANDLE ASSEMBLY,
page 16.  Install handle on 1400
series plate by removing hairpin
form handle mounts. Slide handle
over handle mounts and reinstall
hairpins.

• 1800 Series Handle installation.

Refer to HANDLE ASSEMBLY,
page 16. Remove hex head cap
screws, lockwashers, handle stops and spacers from
shockmounts. Reinstall spacer, handle stop, lockwasher
and hex head cap screw through the handle from the
outside in. Make sure nylon inserts inside of handle
handle stay in place. the handle stop bracket should be
positioned as shown in figure 1, when hardware is tight.

• REMEMBER! It is the owner’s responsibility to

communicate information on the safe use and proper
operation of this unit to the operators.

• Review ALL of the Safety Precautions listed on page 1 of

this manual.

• Familiarize yourself with the operation of the machine

and confirm that all controls function properly.

• Know how to STOP the machine in case of an

emergency.

• Make sure hands, feet, and clothing are at a safe

distance from any moving parts.

• OIL LEVEL - Check the oil level in the engine.  For more

information see “Lubrication” under the respective
engine’s “Owners Manual” or the Maintenance section of
this manual.

• AIR CLEANER - Check to ensure element is in good

condition and properly installed.

• FUEL SUPPLY - The engines on MBW equipment

require an automotive grade of clean, fresh, unleaded
gasoline.

• FUEL FILTER - If clogged or damaged, replace.

Starting Engine

1.

Open fuel valve.

2.

Turn engine switch to “ON”.

3.

Set throttle to idle.

4.

Choke engine if necessary (you may not need to
choke a warm engine).

5.

Pull starter rope repeatedly until engine starts.

6.

After starting engine, open choke gradually and let
engine warm up at idle.

Operating

1.

After engine warms up open fully open throttle. The
compactor will begin vibrating and moving forward.
The number of passes required to reach a desired
compaction level will depend on the type and
moisture content of soil. Maximum soil compactions
has been reached when excessive kickback is
noticed in the compactor.

2.

When using a compactor on asphalt a water
sprinkling system is required to help prevent the
bottom plate from adhering to the hot asphalt surface.

Stopping Engine

1.

Move throttle to idle position.

2.

Let engine idle for one or two minutes.

3.

Turn switch on engine to “STOP” position.

4.

Turn off fuel valve.

Figure 1

Handle Stop

Содержание AP1400






















Отзывы: