background image

4-Channel Amplifiers

FX4.50 / FX4.70 / FX4.100

6

FEATURES:

2 Sets of RCA inputs

- LEVEL: 

Variable sensitivity from 

0.2V to 6V

- BASS EQ:

 Adjustable 45Hz bass boost from 

0dB to 9dB

- X-OVER: 

Selects internal crossover functions

   - FULL: 

Bypasses all crossovers for full frequency operation

   - LP: 

Selects the built in 

LOW PASS

 filter, variable from

 30Hz to 150Hz

   - HP: 

Selects the built in 

HIGH PASS 

filter, variable from 1

0Hz to 1.2kHz

- POWER 

LED

Indicates the powered up and turned on condition

- PROTECTION 

LED

Indicates a high voltage, low voltage, short circuit,

  hard clip, over heating or DC fault condition.

- MODE: 

“2CH” indicates one set of RCA’s are being used. This will also pass signal to channels 3/4 through 1/2 inputs.

   “4CH” indicates connecting 2 sets of RCA’s to 1/2 and
  3/4 inputs.

- LINE OUTPUT: 

Full range RCA pass through.

4 Channel Full Range Stereo:

Control checklist:

Interconnect cable checklist:

- Refer to the section “Settings for Best Performance”

- Connect the four inputs of the amplifier to a Radio/CD with quality RCA cables.
Switch setting checklist:

Minimum final loudspeaker impedances:

- 1/2CH X-OVER:  FULL

- 2 ohm per channel.

- 3/4CH X-OVER:  FULL
MODE: “4CH” since 2 sets of RCA’s are connected.

Important:

 Do not be tempted to connect the hot, or positive outputs, from any source together 

2 or 3 Channel System:

to obtain a mono signal, as this could very well damage the output stage of that source.
- It is necessary to feed the SAME signal to both left and right inputs via a Y-adapter RCA cable.

Here we show how to use the 4 channel amplifiers as a 3 channel unit by taking 

- Connect the mono speaker positive terminal to the Ch4 +, and its negative terminal to Ch3 - as 

advantage of the mono bridging capability of all MB Quart amplifiers. In order to create 

shown.

a 2 channel system, simply follow the example to also mono bridge channel pair 1/2.

Interconnect cable checklist:

Switch setting checklist:

- Connect the inputs of channel pair 1/2 to a suitable stereo source, e.g. a head unit 

- 1/2CH X-OVER:

  FULL

with good quality RCA cables.

- 3/4CH X-OVER:

  LP

- A MONO signal source is required to bridge channel pair 3/4, such as would be 

Control checklist:

available from the mono sub bass output of an active crossover, whether standalone, or 

- Refer to the section 

“Settings for Best Performance”

built into a head unit or equalizer. If you only have 1 set of RCA outputs from your 

Minimum final loudspeaker impedances:

headunit, you can simply connect those to the inputs for ch 1/2 and switch the 

MODE

 to 

- 2 ohm per channel in stereo mode.

2ch. The amplifier will auto sum the signal and provide mono output for bridged 

- 4 ohm mono bridged.

channels 3/4. 

POWER INPUT

GND      REM   BA

TT+12V

  Ch4                          Ch3

  Ch2                          Ch1

-          +          -          +           -          +          -          +

BRIDGED

BRIDGED

FUSE

STEREO LINE INPUT

MONO LINE INPUT

INPUT MODE                           X-OVER                           HIGH PASS                             LEVEL

LP/BP   HP       FULL               30Hz            150Hz                0dB             9dB                 10Hz           1.2kHz              6V                0.2V

OUTPUT                                X-OVER                              LOW PASS                            BASS EQ                           HIGH PASS                            LEVEL                                          INPUT

4CH           2CH          DUPE 3/4    HP      FULL             10Hz           1.2kHz              6V               0.2V

Ch1                Ch3

Ch2                Ch4

Ch 1&2

Ch 3&4

POWER

PROTECTION

INPUT MODE                           X-OVER                           HIGH P

ASS                             LEVEL

LP/BP

   HP

       FULL

               30Hz            150Hz                0dB             9dB                 10Hz           1.2kHz              6V  

              0.2V

OUTPUT                                X-OVER                              LOW P

ASS                            BASS EQ                           HIGH P

ASS                            LEVEL

                                          INPUT

4CH           2CH       DUPE 3/4      HP

      FULL

             10Hz           1.2kHz              6V               0.2V

Ch1                Ch3

Ch2                Ch4

POWER

PROTECTION

POWER INPUT

GND      REM   BA

TT+12V

  Ch4                          Ch3

  Ch2                          Ch1

-          +          -          +           -          +          -          +

BRIDGED

BRIDGED

FUSE

INPUT MODE                           X-OVER                           HIGH P

ASS                             LEVEL

LP/BP

   HP

       FULL

               30Hz            150Hz                0dB             9dB                 10Hz           1.2kHz              6V  

              0.2V

OUTPUT                                X-OVER                              LOW P

ASS                            BASS EQ                           HIGH P

ASS                            LEVEL

                                          INPUT

4CH           2CH       DUPE 3/4      HP

      FULL

             10Hz           1.2kHz              6V               0.2V

Ch1                Ch3

Ch2                Ch4

POWER

PROTECTION

Содержание FORMULA FX1.400












Отзывы: