Maytag HV640HBVIT страница 32 Скачать руководство пользователя

Страница: 32 / 36

REPAIR PARTS LIST

Now that you have purchased your gas water heater, should
a need ever exist for repair parts or service, simply

consult

Maytag Customer Service at 1-800-788-8899 for an
authorized installer on how to control this situation

Be sure to provide all pertinent facts when you call or visit.

The model number of your Gas Water Heater will be found
on the rating place located above the gas control valve.

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE
FOLLOWING INFORMATION:

•

MODEL NUMBER

•

TYPE GAS (NATURAL OR PROPANE (L.P.)

•

SERIAL NUMBER

•

PART DESCRIPTION

THIS IS A REPAIR PARTS LIST, NOT A PACKING LIST.

Model Numbers

Key No.

Part Description

HV640YBVIT

HV650YBVIT

HV640HBVIT

HV650HBVIT

Burner Assembly

TBD

Burner Head

66001494

TBD

Burner Orifice

TBD

66001540

Burner Tube

TBD

HSI Ignition Assembly

TBD

Inner Door

66001499

66001498

66001499

66001498

Inner Door Gasket

66001500

Flue Baffle

TBD

Flue Restrictor

66001513

Blower Assembly

TBD

Air Intake Screen - Base Pan

66001503

Inlet Tube

66001646

66001307

66001646

66001307

Gas Control Valve

TBD

Drain Valve

66001016

Drain Valve Washer

66001021

Outer Door

TBD

Anode Rod

TBD

66001832

TBD

66001832

Temperature-Pressure Relief Valve

66001079

Viewport Assembly

66001509

**20

20" Dia. Drain Pan w/Side Drain (optional)

TBD

22" Dia. Drain Pan w/Side Drain (optional)

TBD

24" Dia. Drain Pan w/Side Drain (optional)

TBD

28" Dia. Drain Pan w/Side Drain (optional)

TBD

*21

Instruction Manual

185374-000

Air Intake Screen - Blower Assembly

TBD

FV Sensor

TBD

FV Sensor Bracket

TBD

**25

Nipple with Heat Trap

TBD

**26

Secondary Anode with Heat Trap

TBD

* Not shown ** Optional TBD (to be determined by Maytag)

OUTER DOOR
(ALTERNATE)

BURNER ASSEMBLY

MAYTAG GAS WATER HEATER

MODEL NO’S

HV640YBVIT

40 Gallon Natural Gas

HV650YBVIT

50 Gallon Natural Gas

HV640HBVIT

40 Gallon Propane (L.P.)

HV650HBVIT

50 Gallon Propane (L.P.)

Содержание HV640HBVIT





































Результаты поиска

Содержание HV640HBVIT

Отзывы:

Похожие инструкции для HV640HBVIT

Бренды по названию

Популярные бренды

Maytag HV640HBVIT, Руководство пользователя

Результаты поиска

Содержание HV640HBVIT

Отзывы:

Похожие инструкции для HV640HBVIT

Бренды по названию

Популярные бренды