manualshive.com logo in svg

Maytag AMV1162AAB/W/Q/S, Сервисная инструкция

Поделиться
Скачать
Maytag AMV1162AAB/W/Q/S Скачать руководство пользователя страница 35

Disassembly Procedures

To avoid the risk of electrical shock, personal injury or
death; disconnect power to oven and discharge
capacitors before following any disassembly procedure.

©2004 Maytag Services

16023056  Rev. 0

35

W AR NIN G

!

Control Key Panel

The key panel has one ribbon connection on the p.c.
board.

The key panel pads can be checked through a continuity
test. Operations of key pad can be checked by
measuring connections at end of ribbon, (using high
ohms scale).

Plastic 

fastener

Holes

Hook

Terminal 

socket

F.P.C.

connector

Control Key Panel Removal

1. Disconnect power to oven.
2. Remove control panel, (see "Control Panel" section).
3. Discharge high voltage capacitor, (see "High Voltage

capacitor section).

4. Disconnect ribbon connector by sliding top part of

connector upward. Once in released position remove
ribbon from connector by siding ribbon side-to-side.

NOTE:

Caution should be used when removing cable

from connector. Ribbon cable has two holes
which connector locks ribbon in place.

5. Peel failed key pad off and replace with new key pad.
6. Reassemble in reverse order.

Outer Case

NOTE:

This procedure requires removal of unit.

1. Disconnect power to oven and remove grille, (see

"Grille" procedure).

2. Remove oven door (see "Door Removal" procedure).
3. Remove screws securing air duct to outer case.
4. Remove screws securing outer case to the chassis.
5. Remove screws securing vent plate to outer case.
6. Remove screw securing power cord cover to outer

case and remove power cord cover (if equipped).

7. Slide outer case towards the rear of the unit, guide

power cord though outer case power cord hole.

8. Place outer case to the side, so no damage will

occur to the case.

9. Reassemble in reverse order.

Vent grille

Controller

Mounting 

plate

Door

Outer case

Vent plate

Power cord cover

Stirrer Assembly

Motor driven antenna assembly is located at the top of
the cavity, using a top feed wave guide.

Stirrer Blade Removal

1. Disconnect power to oven and open the oven door.
2. Carefully pry downward on the plastic rivets securing

the stirrer cover.

3. Rotate slightly and pull down on stirrer fan cover .
4. Reassemble in reverse order.

Models MMV5165A**, MMV5207A**, JMV8208A**

Содержание AMV1162AAB/W/Q/S


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды