manualshive.com logo in svg

Maytag Commercial MLE22PD, Руководство по установке, Страница: 29 / 36

Поделиться
Скачать
Maytag Commercial MLE22PD Скачать руководство пользователя страница 29

29

Factory set for NATURAL GAS: Injector size: 2.2 mm Heat input gross: 5.9 kW

Country:

DE, LU, PL

European Gas Category:

I

2E

Gas Flow Rate:

0.562703 m

3

/hr

Supply Pressure (G20):

20 mbar

Factory Adjusted Pressure (G20):

7.4 mbar

Factory set for Australia/New Zealand NATURAL GAS: Injector size: 2.2 mm  Heat input gross: 5.9 kW

Country:

AU, NZ

Supply Pressure (G20):

minimum 1.13 kPa

Adjusted Pressure (Test Point Pressure):

0.74 kPa

Nominal Hourly Gas Consumption:

21.1 MJ/h

With Australia L.P. Gas Conversion Kit: Injector Size: 1.40 mm  Heat input gross: 6.54 kW

Country:

AU, NZ

L.P. Supply Pressure:

2.75 kPa

Adjusted Pressure:

2.75 kPa

Nominal Hourly Gas Consumption:

23 MJ/h

Factory set for NATURAL GAS: Injector size: 2.2 mm  Heat input gross: 5.0 kW

Country:

NL

European Gas Category:

I

2L

II

2L3B/P

Gas Flow Rate:

0.562703 m

3

/hr

0.562703 m

3

/hr

Supply Pressure (G25):

25 mbar

25 mbar

Factory Adjusted Pressure (G25) :

7.4 mbar

7.4 mbar

Supply Pressure (G30/G31):

Not Applicable

30 mbar

Factory Adjusted Pressure (G30/G31):

Not Applicable

Not Applicable

NOTE: Conversion kit: From Natural Gas to L.P. Gas - Europe: Whirlpool Part No. W10571757.

Conversion kit: From Natural Gas to L.P. Gas - Australia: Whirlpool Part No. W10571729.

Conversion kit: From Natural Gas to Natural Gas - France/Belgium: Whirlpool Part No. W10181947.

Manufacturer: Whirlpool Corporation, Benton Harbor, Michigan 49022, U.S.A.

Manufacturing Site: Whirlpool Corporation, 1300 Marion-Agosta Rd., Marion, OH, 43302, U.S.A.

EU Representatives: Whirlpool EMEA S.p.A., Via Carlo Pisacane, 1, 20016 Pero (MI) Italy

TECHNICAL SPECIFICATIONS – GAS DRYER

Содержание MLE22PD





































Отзывы:

Нет отзывов