FOR SERVICE TECHNICIAN ONLY - DO NOT REMOVE OR DESTROY
PART NO. W10340707A
PAGE 11
QUICK OVERVIEW TEST
■
This cycle consists of 8 steps. In each step, the washer will
perform a Control Action as described in the table below. Once
the action is completed, the washer will advance to the next step.
■
Each step can be differentiated from the others by looking at the
display indication.
■
To advance to the next step before a control action is complete,
press any button
except
QUICK CYCLE.
■
To exit the Quick Overview Test at any time, press the QUICK
CYCLE button.
MANUAL OVERVIEW TEST
Before replacing any system components, perform this
Manual Overview Test.
■
This cycle consists of 7 steps. In each step, the washer will
perform a Control Action as described in the table below. Once
the action is completed, the washer will move to the next step.
Check Exit Condition column.
■
Each step can be differentiated from the others by looking at the
display indication.
■
To move to the next step before a control action is complete,
press any button
except
QUICK CYCLE.
■
To exit the Manual Overview Test at any time, press the QUICK
CYCLE button.
Step
Display Indication
Control
Actuators
Action
to be Checked
1
Delicates
Door locks, drum
■
Door lock system
turns 1/2 revolution,
■
Child safety routine
then door unlocks
■
Motor control (MCU)
and relocks.
2
CCU
Fill by both cold water
■
Cold water inlet valves
EEPROM Version
inlet valves (4 liters)
■
#1 and #2
into BLEACH
■
Pressure switch:
& Knits
compartment.
■
Suds Level
3
CCU
Fill by hot water inlet
■
Hot water inlet valve
Software Version
valve to Wash Level
■
Pressure switch:
into MAIN WASH
■
Wash Level
Delicates & Knits
compartment.
4
MCU
Software Version
Drum executes
Whites
tumbling at
■
Motor
5
MCU
wash speed
■
Motor control (MCU)
Hardware Version
(30 sec).
Bright
6
UIC
Drain pump is ON.
■
Drain pump
EEPROM Version
■
Pressure switch*
Colors
7
UIC
Drum rotates
■
Motor
Software Version
counter-clockwise
■
Motor control (MCU)
and ramps up.
■
Drain pump on
Permanent Press
Performs unbalance
procedure before and
after spinning. If not
interrupted, the drum
will slow and stop;
after reaching 0 rpm,
the door unlocks and
Step 8 will be skipped.
8
Delicates
This Step is only
■
Door unlock
apparent if Step 7 is
MANUALLY ADVANCED
prior to the drum
reaching 0 rpm
(washer pumps out
if needed). Door
unlocks (washer
returns to flashing
mode).
Exit
Step
Display
Condition
Control
To be
Action
Checked
1
Delicates
On
Door locks, drum
■
Door lock system
completion
turns 1/2 revolution,
■
Child safety routine
only
then door unlocks
and relocks.
2
& Knits
On
Filling with both
■
Cold and Hot Water
button press valves.
Inlet Valve
or if overfill
■
Overfill level
level is
detected
3
Colors
On button
Drum executes
■
Motor
press or
reversing movement
■
Motor Control (MCU)
completion
at wash speed
(10 min.).
4
Permanent
On button
Drain pump is on
■
Drain Pump
Press
press or
(4 min.).
completion
5
Delicates
On
Drain pump is on
■
Drain Pump
completion
(reach Level_sud
only
plus 10 sec.).
6
& Knits
On button
Drum rotates counter-
■
Motor
press or
clockwise and ramps
■
Motor Control (MCU)
completion
up to maximum speed.
7
Delicates
On button
Stop motor to 0 rpm.
■
Motor
& Knits
press only
Door unlocks.
■
Motor Control (MCU)
after rpm = 0
■
Door lock system
and door is
unlocked
The drain pump may be running in any of the last 3 steps, depending
on the water level in the washer and position of the pressure switch.
*The washer will drain until pressure switch reaches lowest level
for 10 seconds, then moves to next step.
The drain pump may be running in any of the last 3 steps, depending
on the water level in the washer and position of the pressure switch.