background image

17

1. 

Place towel on dryer

Place towel on top of dryer to avoid damaging the surface.

Lift door until top screws in dryer cabinet are in large part of 

hinge slot. Pull door forward off screws. Set door (handle side 

up) on top of dryer. Remove top screws from dryer cabinet.

3. 

Lift door off top screws

2. 

Remove bottom screws

Open dryer door. Remove bottom screws from dryer cabinet 

side of hinges. Loosen (do not remove) top screws from dryer 

cabinet side of hinges.

COMPLETE INSTALLATION 

CHECKLIST

  Check that all parts are now installed. If there is an extra 

part, go back through steps to see what was skipped.

  Check that you have all of your tools.

  Dispose of/recycle all packaging materials.

  Check dryer’s fi nal location. Be sure vent is not crushed 

or kinked.

  Check that dryer is level. See “Level Dryer.”

  Remove fi lm on console and any tape remaining on dryer.

  Wipe dryer drum interior thoroughly with a damp cloth to 

remove any dust.

  Read “Dryer Use” in your Use and Care Guide.

  Set the dryer on a full heat cycle (not an air cycle) 

for 20 minutes and start the dryer.

If the dryer will not start, check the following:

 

Controls are set in a running or On position.

 

Start button has been pushed fi rmly.

 

Dryer is plugged into an outlet and/or electrical supply 

is on.

 

Household fuse is intact and tight, or circuit breaker has 

not tripped.

 

Dryer door is closed.

 

When the dryer has been running for 5 minutes, open the 

dryer door and feel for heat. If you feel heat, cancel cycle 

and close the door.

If you do not feel heat, turn off dryer, and check the 

following:

 

There may be two household fuses or circuit breakers 

for the dryer. Check that both fuses are intact and tight, 

or that both circuit breakers have not tripped. If there 

is still no heat, contact a qualifi ed technician.

NOTE:

 You may notice an odor when the dryer is fi rst heated. 

This odor is common when the heating element is fi rst used. 

The odor will go away.

REVERSE DOOR SWING 

(OPTIONAL)

NOTE: 

Magnetized screwdriver is helpful.

27" Wide Model Side-Swing Door

Содержание MEDP575G





















Отзывы: