Maxwell MW-3245, Инструкция по эксплуатации

Страница: 8 / 20

8
ENGLISH
•
For children safety reasons do not leave poly-
ethylene bags used as packaging unattended.
Attention! Do not allow children to play with poly-
ethylene bags or packaging film. Danger of suf-
focation!
• Regularly check the power plug and power cord
integrity for damages.
• Never use the unit if the power cord or the power
plug is damaged, if the unit works improperly or
after it was dropped.
•
If the power cord is damaged, it should be replaced
by the manufacturer, a maintenance service or
similar qualified personnel to avoid danger.
• Do not repair the unit by yourself. Do not dis-
assemble the unit by yourself, if any malfunc-
tion is detected or after it was dropped, unplug
the unit and contact any authorized service
center from the contact address list given in
the warranty certificate and on the website
www.maxwell-products.ru.
•
Transport the unit in the original packaging only.
• Keep the unit out of reach of children and peo-
ple with disabilities.
THIS UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY. ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
SAFETY PRECAUTIONS
•
Do not use the vacuum cleaner near hot surfac-
es, ashtrays and in places where inflammable
liquids are stored.
• Take sharp objects away from the floor before
cleaning to prevent unit damage.
BEFORE THE FIRST USE
After unit transportation or storage at low tem-
perature keep it for at least three hours at room
temperature.
– Unpack the unit completely and remove any
advertising stickers that can prevent the unit
operation.
–
Check the unit for damages; do not use a dam-
aged unit.
–
Before switching the unit on, make sure that the
mains voltage corresponds to the unit operat-
ing voltage and the switch (5) is set to “O” (off)
position.
ASSEMBLING THE VACUUM CLEANER
To use the vacuum cleaner in a vertical mode, attach
the extension pipe (3). To do this, open the clamp in
the upper part of the handle (4) and insert the exten-
sion pipe (3) into the opening. Press the clamp until
clicking, it means that the handle (3) is fixed (pic. 1).
To use the vacuum cleaner in a hand-held mode,
remove the extension pipe (3). To do this, open the
clamp on the handle (4) and pull the extension pipe
(3) to remove it from the handle (4) (pic. 2).
Installing and removing the brushes/
attachments
Insert the floor brush (9) into the opening for at-
tachments in the bottom part of the dust bin (8)
flask. To remove the brush, pull it away from the
vacuum cleaner body.
The small brush (10) and the crevice nozzle (11) are
installed in a similar way.
The small brush (10) is intended for removing dust
from smooth surfaces of furniture, books or fragile
objects, such as picture frames etc. It is suitable
for thorough cleaning of soft furniture, mattresses,
cushions, curtains etc.
The crevice nozzle (11) is intended for cleaning
folds on fabric, grooves, joints, corners or niches
that the floor brush cannot reach.
USING THE VACUUM CLEANER
ATTENTION! You may switch the vacuum cleaner
on only with the dust bin (8) and the HEPA filter (7)
installed in it. Before switching the vacuum cleaner
on always make sure that the HEPA filter (7) is
installed properly in the dust bin (8) and that the
switch (5) is in “O” (off) position.
–
Before using the unit, unwind the power cord (2)
to its full length and insert the power plug into
the mains socket.
– To quickly unwind the power cord (2), turn the
upper holder (12) 90 degrees and remove the
power cord (2).
Note: You can adjust the power cord (2) length, if
necessary, by winding it on the holders (12).
–
To switch the vacuum cleaner on, set the switch
(5) to “I” (on) position.
–
After you finish cleaning the room, set the
switch (5) to “O” (off) position, install the vacu-
um cleaner vertically and unplug it.
– To wind the power cord (2) use the holders (12).
Note
The vacuum cleaner is equipped with a thermostat
which will automatically switch the unit off in case of
overheating. If it happened:
–
Switch the unit off and unplug it.
– Let the unit cool down. When the unit cools
down, check and clean the filter (7).
– Insert the power plug into the mains socket and
switch the vacuum cleaner on.
CLEANING THE VACUUM CLEANER
It is recommended to clean the vacuum cleaner after
every use. Before cleaning the vacuum cleaner, switch