Maxwell MW-1753 PK, Инструкция по эксплуатации

Страница: 9 / 40

ENGLISH
9
Note : - If you disconnect the unit from the mains
and then connect it again, and water in the
thermopot is still hot, the unit will be switched
on in the keep warm mode (the «KEEP WARM»
indicator (20) lights up). To switch the boiling
mode on press the «START/RE-BOIL» button
(19).
–
After water starts boiling, the thermopot will
be switched to the keep warm mode, the
«KEEP WARM» indicator (20) will light up.
– You can switch the reboiling on after water
boiling, when the unit is operating in the
keep warm mode and the «KEEP WARM»
indicator (20) lights on the control panel.
Press the «START/RE-BOIL» button (19), the
«BOILING» indicator (18) will light up.
–
Ensure that water level is not below the mark
(1) and not above the «FULL» mark (11). If the
water level is below the mark (1), open the lid
(8) and refill the thermopot with water.
–
Pour water out of the thermopot into a suit-
able bowl, placing it under the spout (3).
Water can be dispensed in the following
ways:
–
by unlocking and pressing the hand pump
(6),
– by pressing and holding the «WATER
DISPENSE» button (21) (pic. 4).
Note:
- The «WATER DISPENSE» button (21) is active
only when the unit is connected to the mains.
Attention!
• Dispense water only after boiling is fin-
ished (the «KEEP WARM» indicator (20)
lights up).
•
You can lock/unlock the hand pump (6)
using the lock (9):
« » - the pump is locked,
« » - the pump is unlocked.
– After use disconnect the unit from the mains
by unplugging the power plug (17) and
detaching the power cord from the socket
(14).
–
To pour out the remaining water wait till the
unit cools down completely and then remove
the lid (8). Open the lid (8) by pressing the
button (5) and pull it (pic. 1), then remove
the lid (8) by pressing and holding the lock
(10) (pic. 5).
–
To install the lid (8) back to its place, insert
the metal spindle of the lid (8) into the lock
(10) groove and release the lock (10).
–
Let the unit cool down and take it away for
storage.
Cleaning and care
–
Before cleaning, disconnect the unit from the
mains, let the thermopot cool down and pour
out water.
– Clean the thermopot outer surface with a soft
damp cloth and then wipe it dry. Do not use
metal brushes, abrasives and solvents.
–
Do not immerse the thermopot, the power
cord and plug into water or other liquids.
– Do not wash the thermopot in a dishwashing
machine.
Stains on the inner surface of the
thermopot
The inner metal surface may change its color
under the influence of different water impurities.
–
To remove the stains wet a cloth with citric
acid or vinegar and wipe the inner surface of
the thermopot flask.
–
To remove the citric acid or vinegar taste boil
water and pour it out. Repeat this procedure
till the smell and taste vanish completely.
Descaling
–
Scale, appearing inside the thermopot, influ-
ences the water taste and disturbs the heat
exchange between water and heating ele-
ment.
–
To remove the scale fill the thermopot with a
mixture of one part ordinary vinegar and two
parts water till the maximal level mark (11)
«FULL».
– Plug the unit in, let the mixture boil and leave
the unit operating in the keep warm mode
for 1 hour.
–
Reboil water pressing the «START/RE-BOIL»
button (19).
–
Once the mixture starts boiling and the unit
is switched to the keep warm mode, unplug
the unit.
–
Let the unit cool down and then pour out the
mixture, preliminary removing the lid (8).
–
After descaling boil and pour out clean water
several times.
MW-1753.indd 9 28.03.2013 15:34:40