©2002 Digital Security Controls Ltd.
Toronto, Canada •
www.dsc.com
Technical Support 1-800-387-3630
Printed in Canada 29005815 R005
Direct all comments and suggestions
concerning DSC publications to
FCC COMPLIANCE STATEMENT
CAUTION:
Changes or modifications not expressly approved by Digital Security
Controls Ltd. could void your authority to use this equipment.
This equipment generates and uses radio frequency energy and if not installed and
used properly, in strict accordance with the manufacturer’s instructions, may cause
interference to radio and television reception. It has been type tested and found to
comply with the limits for Class B device in accordance with the specifications in
Subpart “B” of Part 15 of FCC Rules, which are designed to provide reasonable
protection against such interference in any residential installation. However, there is
no guarantee that interference will not occur in a particular installation. If this equip-
ment does cause interference to television or radio reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Re-orient the receiving antenna
•
Relocate the alarm control with respect to the receiver
•
Move the alarm control away from the receiver
•
Connect the alarm control into a different outlet so that alarm control and receiver
are on different circuits.
If necessary, the user should consult the dealer or an experienced radio/televi-
sion technician for additional suggestions. The user may find the following
booklet prepared by the FCC helpful: “How to Identify and Resolve Radio/
Television Interference Problems”. This booklet is available from the U.S. Gov-
ernment Printing Office, Washington, D.C. 20402, Stock # 004-000-00345-4.
PC4204CF Outputs
Module Number: PC4204CF
Module Number: PC4204CF
Module Number: PC4204CF
Module Number: PC4204CF
Module Number: PC4204CF #
I______I______I
(1-16 = XX)
Partition
Output
1 2 3 4 5 6 7 8
Zone
Schedule #
Pulse Timer
[000702XX01] PC4204CF Relay 1
I______I______I I______I______I______I______I______I______I______I______I
I______I______I______I
I______I______I
I______I______I______I
[000702XX02] PC4204CF Relay 2
I______I______I I______I______I______I______I______I______I______I______I
I______I______I______I
I______I______I
I______I______I______I
[000702XX03] PC4204CF Relay 3
I______I______I I______I______I______I______I______I______I______I______I
I______I______I______I
I______I______I
I______I______I______I
[000702XX04] PC4204CF Relay 4
I______I______I I______I______I______I______I______I______I______I______I
I______I______I______I
I______I______I
I______I______I______I
4. Enrolling the Module
Once connected, the module must be enrolled on the system. To enroll
the module, perform the following:
1. Enter Installer Programming by pressing [*] [8] [Installer Code].
2. Scroll to “Module Hardware” and press the [*] key.
3. Scroll to “Enroll Module” and press the [*] key.
4. Scroll through the different modules until “PC4204” is displayed.
Press the [*] key.
5. The message “Create Tamper on Desired Unit” will be displayed.
To create the required tamper, secure the tamper zone on the
module and then open it. The transition from secure to violated
enrolls the module. After this is done, the keypad will display
the module number and will confirm enrollment (e.g., “PC4204
Mod 01 Enrolled”).
For more information regarding module enrollment, see the control
panel
Installation Manual.
5. Programming the Module
To access PC4010CF/PC4020CF programming, enter [*][8] followed
by the Installer Code. Each relay output must be programmed. Please
see the control panel
Installation Manual and Programming Worksheets
for a detailed list of output options.
NOTE:
Relay 1 must not be programmed if used for Combus power. Ensure
that Jumper CON3 is set to “Repower Relay1.”
NOTE:
PC4204CXCF relay outputs cannot be used for fire system notification
appliances.
