MaxStream 9XCite XC09-009 Series Скачать руководство пользователя страница 28

Страница: 28 / 37

Distributor of Digi International: Excellent Integrated System Limited

Datasheet of XC09-009-DK - KIT DEV FOR 900MHZ 9600BPS 1MW
Contact us: [email protected] Website: www.integrated-circuit.com

9XCite™

OEM

Module

–

Product

Manual

v2.1

[2007.01.04]

2007

MaxStream,

Inc.

RT (DI2 Configuration) Parameter

<Non-AT Settable Parameter: Serial Interfacing>
RT Parameter enables RTS Mode.

SB (Stop Bits) Parameter

<Non-AT Settable Parameter: Serial Interfacing>
SB Parameter allows the user set the number of
stop bits used in data transmission.

SH (Serial Number High) Command

<AT Command: Diagnostic> SH Command reads and returns the RF module serial number high
word.

AT Command: SH

Parameter Range: 0 - 0xFFFF [Read-only]

# of bytes returned: 2

Related Command: SL (Serial Number Low)

SL (Serial Number Low) Command

<AT Command: AT Command Options> SL Command reads and reports the RF module serial
number low word.

AT Command: SL

Parameter Range: 0 - 0xFFFF [Read-only]

# of bytes returned: 2

Related Command: SH (Serial Number High)

Parameter Ranges: 0 - 1

Parameter

Configuration

disabled

Enables RTS

Handshaking

Default Parameter Value: 0
Number of bytes returned: 1

Parameter Ranges: 0 - 1

Parameter

Configuration

1 stop bit

2 stop bits

Default Parameter Value: 0
Number of bytes returned: 1

28 / 37

Содержание 9XCite XC09-009 Series






































Результаты поиска

Содержание 9XCite XC09-009 Series

Отзывы:

Похожие инструкции для 9XCite XC09-009 Series

Бренды по названию

Популярные бренды

MaxStream 9XCite XC09-009 Series, Руководство по эксплуатации продукта

Результаты поиска

Содержание 9XCite XC09-009 Series

Отзывы:

Похожие инструкции для 9XCite XC09-009 Series

Бренды по названию

Популярные бренды