Maxon GPSLR Series Скачать руководство пользователя страница 6

Страница: 6 / 33

1. Incorrect operation of this Liftgate can result in serious personal

injury. Comply with

WARNINGS

and Liftgate operating instructions

in this manual. Do not allow untrained persons or children to operate

the Liftgate. If you need to replace an

Operation Manual

, additional

copies are available from:

MAXON Lift Corp.

11921 Slauson Ave

Santa Fe Springs, CA 90670

(800) 227-4116

WARNING

NOTE:

For latest version manuals (and replacements), down-

load manuals from Maxon’s website at

www.maxonlift.com.

2. Do not exceed rated load capacity of the Liftgate, which is

3300 lbs. for the GPSLR-33 & GPSTLR-33, and 4400 lbs. for
the GPSLR-44

& GPSTLR-44.

4. Consider the safety and location of bystanders and

location of nearby objects when operating the Liftgate. Stand

to one side of platform while operating the Liftgate. Be certain

that the area the Liftgate will move through during operation

is clear of all obstacles.

5. Comply with all attached instruction decals and warning decals.

11. Above all,

USE GOOD COMMON SENSE

when operating the

Liftgate.

8. Do not move vehicle unless Liftgate is correctly stowed.

6. Keep decals clean and legible. If decals are illegible or missing,

have them replaced.

Get free replacement decals

from

Maxon.

Never drive a forklift on the Liftgate platform.

10. A correctly installed Liftgate will operate smoothly and reasonably

quiet. The only noticeable noise, during Liftgate operation, is from

the power unit while the platform is raised. Listen for scraping,

grating and binding noises and have the problem corrected

before continuing to operate the Liftgate.

Correctly stow platform when not in use. Extended platforms

could create a hazard for people and vehicles passing by.

3. Do not allow any part of your body to be placed under, within, or

around any portion of the moving Liftgate or its mechanisms, or in

a position that would trap them between the platform and the fl oor

of truck body (or between platform and the ground) when Liftgate is

operating.

12. Never use a cell phone while operating the Liftgate.

WARNINGS

Содержание GPSLR Series


































Результаты поиска

Содержание GPSLR Series

Отзывы:

Похожие инструкции для GPSLR Series

Бренды по названию

Популярные бренды

Maxon GPSLR Series, Руководство по эксплуатации

Результаты поиска

Содержание GPSLR Series

Отзывы:

Похожие инструкции для GPSLR Series

Бренды по названию

Популярные бренды