Maxon ACC-513E Скачать руководство пользователя страница 6

Страница: 6 / 38

Modulation type:

FFSK

Maximum RF Baud rate:

2400 (12.5 KHz) channel spacing and 4800 (25 KHz) channel
spacing (Programmable, see below table)

Data Sensitivity:

below

–

110dBm for 1 in 100 error rate

Mark /Space tone freq. (for each available RF Baud rate):
1200Hz (M) / 1800Hz (S) at 1200bps
1200Hz (M) / 2400Hz (S) at 2400bps
2400Hz (M) / 4800Hz (S) at 4800bps

Data input/output:

RS232

RS232 Baud input rate:

follow the RF Baud rate (see below table)

Number of Data Bit:

8 bits

Parity:

None

Number of Stop Bit:

1 bit

Data flow control:

None, Software (Xon/Xoff),
Hardware (RTS/CTS) (Programmable)

Tx forcing mode:

Configures the modem to transmit regardless of squelch state

Data Block (Packet) size:

Programmable from 16bytes to 8192bytes by multiple of 16
bytes increments. To provide maximum flexibility, packet
doesn

’

t include additional bits for error detection and correction.

We recommend that the users add their own methods for
error detection/correction.

Table 2.2. Available Baud rate for FFSK modem

Содержание ACC-513E







































Результаты поиска

Содержание ACC-513E

Отзывы:

Похожие инструкции для ACC-513E

Бренды по названию

Популярные бренды

Maxon ACC-513E, Техническое руководство

Результаты поиска

Содержание ACC-513E

Отзывы:

Похожие инструкции для ACC-513E

Бренды по названию

Популярные бренды