manualshive.com logo in svg

Maxon ACC-513E, Техническое руководство

Поделиться
Скачать
Maxon ACC-513E Скачать руководство пользователя страница 18

 
c. TX Forcing Mode 

During RX mode, when the Radio receives data from the DTE, if 

TX Forcing Mode 

Option is enable, the radio will transmit data. If disabled, the radio will not. 

 

d. Initializing Data for HT (Hyper Terminal) 
This is a strongly recommended option when using Hyper Terminal. In addition, you 
can check the version of the modem. 
 

 
6.3. System Option 2 

 

a. Base Block Size 1 
This option is about the data size to be transmitted at one time. If data flow control 
is selected in Auto mode, radio will try handshaking after a transmission of 

assigned data. you can select the 

Base Block Size1 according to communication 

conditions. Proper value is maximum data size to complete successful transmission 
without any error. Usually, under 128 byte (Default) is recommended. Detailed 
information is given in Section 7.4. 

 

b. Preamble Data Size 
This size of bit is for synchronization of the modem. At least 32 bits (Default) is 
recommended. Detailed information is given in Section 7.4. 

 

c. Wait for Busy Time 
After the radio transmits established data, the radio waits for a response signal. If 
there is no response signal, after this specified time elapses, next data will be 
transmitted, next data will be transmitted on receiving response signal. Normally, 
1000ms (Default) is recommended. 

 

d. Flow Control 
There are three methods to control data. Under Auto Mode, you can select 
Xon/Xoff, RTS/CTS or NONE but in Dumb Mode, this is fixed to NONE. Detailed 
information is given in Section 7.1. 
 

Software : Flow Control is controlled by Xon/Xoff code. 

Hardware : Flow Control is controlled by RTS/CTS of RS-232 
None : Radio does not use any Flow Control. 

 
e. Tx Delay Time 1 
In Auto Mode, to prevent frequent transmission due to irregular data input, this 
option allows for the radio to enter transmission mode after an assigned time. For 
your reference, frequent transmission spends too much time for its preparation 

Содержание ACC-513E







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды