MAXIMATOR RM350 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 18

background image

RM350

INSTALLATION AND COMMISSIONING

RM350 GAS CONTROLLERS

MAY 16

13 of 18

Overload

This signal is used for safety and the controller will show an overload alarm in the status page if the
overload trips out on the hydraulic power pack.

GAS Controlle

r

Injection Moulding Machine

NOTE

:

All connections must be volt free at

IMM.

Suggested Connections IMM:

Overload auxiliary contact

Oil Temperature

This signal is used for safety and the controller will show an oil temperature alarm in the status page if
the oil temperature goes above its set level..

GAS Controlle

r

Injection Moulding Machine

NOTE

:

All connections must be volt free at

IMM.

Suggested Connections IMM:

Temperature switch

Oil Level

This signal is used for safety and the controller will show an oil level alarm in the status page if the oil
level falls below its minimum set point.

GAS Controlle

r

Injection Moulding Machine

NOTE

:

All connections must be volt free at

IMM.

Suggested Connections IMM:

Level switch

Pressure Bypass

This signal is used to actuate the pressure bypass solenoid on the external hydraulic power pack.

GAS Controlle

r

Injection Moulding Machine

NOTE

:

All connections must be volt free at

IMM

.

«
...
11
12
13
14
15
...
»

Содержание RM350



















Отзывы:

Нет отзывов

Похожие инструкции для RM350

Бренд: Fairchild Страницы: 2

Бренд: Fagor Страницы: 103

Бренд: Harman Страницы: 2

Бренд: T-Link Страницы: 3

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 6

EIP-2000 Series

Бренд: ICP DAS USA Страницы: 19

Бренд: GBD Страницы: 15

Бренд: ZIGBEE Страницы: 5

Бренд: WAGO Страницы: 16

Бренд: Roger Страницы: 21

Бренд: Cypress Страницы: 3

IB-TRON 4000 SOL

Бренд: INSBUD Страницы: 14

Бренд: babyplus Страницы: 28

Бренд: phytron Страницы: 55

Бренд: schmersal Страницы: 6

Бренд: Water Specialist Страницы: 36

8745 MFC Ethernet

Бренд: Burkert Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды