Maxim M190G Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 69

Maxim M190G Скачать руководство пользователя страница 18

1-14

Overview and Operating Principle

Returning (Refer to Figs. 1.15 and 1.16)

When the paper feeding lever moves in the direction of arrow (b) in Fig. 1.15 along the groove
cam on the Cam,paper feeding, the Gear,paper feeding drive rotates in the direction of arrow (c)
in Fig. 1.15. After paper is fed one gear tooth, the Gear,paper feed drive returns to the paper free
state (in the state which tooth section of the Gear,paper feeding drive disengages the tooth
section of the Gear,paper feeding. (refer to the Section "Paper Free".) After the paper feeds two
gear teeth the Gear,paper feeding drive is returned by passing over the gear teeth of the
Gear,paper feeding. At this time, the shaft for the Gear,paper feeding which is blocked by the
detent spring disengages from the paper feeding gear and the paper feeding gear rotates in
reverse, returning it to the home position.

Figure 1-16 Operation of Gear,paper feeding drive and Gear,paper feeding

while Paper Feeding and Returning

Paper free

The Lever,release is rotated in the direction of arrow (a) in the Fig. 1.17 by cam A of the
Cam,paper feeding. This causes the Gear,paper feeding drive to slide in the direction of arrow
(b) and disengage the Gear,paper feeding drive from the Gear,paper feeding. This condition is
referred to as the "Paper free state" below.) Even when the Cam,paper feeding cam rotates in the
direction of arrow (c) to stop cam A, the cam cannot be controlled. The paper free state is
maintained as long as the Cam,paper feeding remains in contact with the Lever,fast feeding due
to the structure, thus, the paper free state continues until the cam of the paper feeding cam is
released from the Lever,fast feeding.

Gear, paper feeding drive

Roller, paper feeding

Spring, brake

Gear, paper feeding drive

Gear, paper feeding

Normal position

Gear, paper feeding

When paper feeding

«
...
16
17
18
19
20
...
»

Содержание M190G






































































Отзывы:

Нет отзывов