Maxim Integrated MAX9277 Скачать руководство пользователя страница 1

Страница: 1 / 72

General Description

The MAX9277/MAX9281 are 3.12Gbps Gigabit Multimedia

Serial Link (GMSL) serializers with 3- or 4-data lane LVDS

input (oLDI) and a CML serial output programmable for

50Ω coax or 100Ω shielded twisted pair (STP) cable drive.

The MAX9281 has HDCP content protection but other

wise is the same as the MAX9277. The serializers pair

with any GMSL deserializer capable of coax input. When

programmed for STP output they are backward compat

ible with any GMSL deserializer. The output amplitude is

programmable 100mV to 500mV single-ended (coax) or

100mV to 400mV differential (STP).
The audio channel supports L-PCM I

S stereo and up to

eight channels of L-PCM in TDM mode. Sample rates of

32kHz to 192kHz are supported with sample depth up to

32 bits.

The embedded control channel operates at 9.6kbps to

1Mbps in UART-UART and UART-I

C modes, and up to

1Mbps in I

C-I

C mode. Using the control channel, a µC

can program serializer, deserializer and peripheral device

registers at any time, independent of video timing, and

manage HDCP operation (MAX9281). A GPO output sup

ports touch-screen controller interrupt requests from the

remote end of the link.

For use with longer cables, the serializers have program

mable pre/deemphasis. Programmable spread spectrum

is available on the serial output. The serial output meets

ISO 10605 and IEC61000-4-2 ESD standards. The core

supply is 1.7 to 1.9V and the I/O supply is 1.7 to 3.6V. The

package is a lead-free, 48-pin, 7mm x 7mm TQFN with

exposed pad and 0.5mm lead pitch.

Applications

● High-Resolution Automotive Navigation

●

Rear-Seat Infotainment

● Megapixel Camera Systems

Features and Benefits

● Ideal for High-Definition Video Applications

•

Drives Low-Cost 50Ω Coax Cable and FAKRA

Connectors or 100Ω STP

• 104MHz High-Bandwidth Mode Supports

1920x720p/60Hz Display With 24-Bit Color

•

Serializer Pre/Deemphasis Allows 15m Cable at

Full Speed

• Up to 192kHz Sample Rate and 32-Bit Sample

Depth For 7.1 Channel HD Audio

● Multiple Data Rates for System Flexibility

• Up to 3.12Gbps Serial-Bit Rate

•

6.25MHz to 104MHz Pixel Clock

•

9.6kbps to 1Mbps Control Channel in UART,

mixed UART/I

C, or I

C Mode with Clock Stretch

Capability

● Reduces EMI and Shielding Requirements

•

Serial Output Programmable for 100mV to 500mV

Single-Ended or 100mV to 400mV Differential

•

Programmable Spread Spectrum Reduces EMI

•

Bypassable Input PLL for Pixel Clock Jitter

Attenuation

•

Tracks Spread Spectrum on Input

•

High-Immunity Mode for Maximum Control-

Channel Noise Rejection

● Peripheral Features for System Power-Up and

Verification

•

Built-In PRBS Generator for BER Testing of the

Serial Link

•

Programmable Choice of 9 Default Device

Addresses

•

Dedicated “Up/Down” GPO for Touch-Screen

Interrupt and Other Uses

•

Remote/Local Wake-Up from Sleep Mode

● Meets Rigorous Automotive and Industrial

Requirements

•

-40ºC to +105ºC Operating Temperature

•

8kV Contact and 15kV Air ISO 10605 and

IEC 61000-4-2 ESD Protection

Ordering Information

appears at end of data sheet.

19-6764; Rev 3; 10/17

MAX9277/MAX9281

3.12Gbps GMSL Serializers for Coax or

STP Output Drive and LVDS Input

EVALUATION KIT AVAILABLE

Содержание MAX9277









































































Результаты поиска

Содержание MAX9277

Отзывы:

Бренды по названию

Популярные бренды

Maxim Integrated MAX9277, Руководство пользователя

Результаты поиска

Содержание MAX9277

Отзывы:

Бренды по названию

Популярные бренды